Search results for query: *

I have an angry cam in my 318 and have always struggled to get it tuned good for idle --- edelbrock 600 carb -recently tore it all down and cleaned ot all etc and have been tinkering to reset stuff....have the idle as good as it will ever be, but in my tinkering today I had a rude surprise....I...

Looking for the parts to refurbish my 72 Cuda 2 speed wiper linkage "cam" section.... Need all the parts shown below (my old parts) plus the boot and clip and wavy washer...etc. basically everything. Tell me what you have and how much shipped to 15132. Thanks

I am needing the parking light lenses for the front of a 72 Barracuda.... Let me know if you can help. Thanks!

Will be traveling from NYC to PGH today...will be passing by many of you.... Looking for parts for a 72 Barracuda: - driveshaft (727 tranny yoke, small driveshaft pinion) - front bumper - lower grill - 22" radiator shroud I know its short notice...just got good internet service back...

Hey folks....just started looking for a a driveshaft and tranny crossmember for 72 Barracuda that is running an 8 3/4 rear end (2.76 gears, small yoke I think?) and a 1976 318 engine..... Can anyone give me an idea of what I should expect to pay, used, for these and what length etc I might be...

Need to replace the master cylinder cover and gasklet on my 72 fish....cant find one anywhere so far....figured I would go chrome while I was at it... Any ideas for finding one? If I could at least find a new gasket.....mine is leaking and I cant proceed with bleeding brakes and such til I get...

Anyone know off-hand the fitting size for the fuel line connection at the discharge side of the fuel pump on a 76 318? I believe that in stock form there is a steel fuel line that runs from the pump up to the carb.... I have an edelbrock 4v carb and it has a hose inlet, so i am looking to...

I am looking for a few (many) things for my 72 Barracuda with a 76 318 in it.... But the most "urgent" ones: -- fan and viscous drive (temp controlled one) -- bolts for radiator -- radiator shroud and bolts -- lower grill/light housing assembly -- mini starter *FOUND* -- bolts for starter...

I bought a steering wheel and pulley puller set, but the longest bolts and the center part is still about an inch short due to the depth of the crush can. The manual calls for chrysler tool # C3428B....and my bet is that is PRICEY. What are you guys using to pull the steering wheel?

Well, a neighbor into E bodies came up and was checking out my project car ...72 Barracuda. I was told it had a 74 318 in it.....Well, my neighbor ID'd the heads as "J" heads (He pointed out the "J" on them) and said he thought I might actually have a 360......so , now that he got my curiosity...

am working on getting the ignition in my 72 fish reconnected.72 body, 74 318 engine.... I got the Bill Evans engine harness for electronic ignition and it has two 2-spade connectors for the ballast. My car had a single ballast so I went to my local Pep Boys and bought a new dual unit. Couple...

Who do you guys use for your antique auto insurance? I am considering having my 72 fish plated as antique..its currently titled regular, and going to antique requires having the coeverage at the time of having the title changed and getting the plate.... Can you folks recommend anyone...

I have the console shifter in my 72.....but the handle is broken.....I have it , but its broken and split and has no internal parts for the button..... Is my only choice here a repro at $45-60?

I have a 74 318 in my 72 Barracuda.....need to get the ecu box.....I am not sure how the motor is built.....but I was told it was rebuilt to factory specs 5 years ago. Should I get the orange or chrome box, as I see the chrome has "a hotter spark".......its only a $20 difference but if it is...

Wasn't sure where to post this one so here it is...my apologies if it needs to be in another area.....:o Got the 72 Barracuda home and just now getting around to tinkering wit hstuff wwhat with all the other "stuff" that had to happen to make this happen. Finally realizing that this baby is...

My car needs a starter and I am planning headers so I know I want a mini-starter.... I seem to remember seeing a post a while back saying that the newer 318 engine starters were smaller..... Or is the Mopar Performance mini starter the only way to go? Any other info I need to know when buying...

Just starting to sort stuff out on my 72 Barracuda.... The 74 318 that is in it came from another car.... The motor has a battery cable (ground) coming from it (drivers side front corner of the block), and my car has a ground battery cable that goes to the radiator support. So trying to...

The 74 318 currently sitting in my 72 Barracuda has stock exhaust manifolds on it and no exhaust.....she has power steering and will have an automatic (planning a 727). I know I want headers, just not sure which ones work the best at a reasonable price. Less money the better, but I also want...

I am headed out tomorrow to check out a 72 Barracuda.... It was a barn find that had no tranny or engine in it.....bought by a body shop and redone to the point it is at. It has been recently redone body and undercarriage, stripped and repainted. They told me there is very little bondo in the...

Hi all... New to the forum....have been hangin garound on the a body forum for a little bit now, thought I would register here too.... I am looking for an ole' Mopar......I have always dreamed of a Challenegr or Cuda but because the prices seem to be so high on them, even in poor shape, I...