Search results for query: *

That`s awesome , thx alot for this tipp :)

Hi I have change my ignition switch in the Lock Housing and with reassemble I made a mistake where I not know what it be and I hope one of you could help me find out what went wrong , because the Lock Housing are not fixed as it should be and when I turn on the Steering Wheel the Lock Housing...

So I have to made both wires from the Ballast Resistor together and but them to the Coil + , right ? From Ignition Switch wireing the brown wire are the Ignition + , Position 2 from the key and the blue one are Ignition + , Position 1 from the key right ? I must check the ground . Normaly it...

Hi I have Ignition Problems and I try to repair this from May to now but nothing what I do are work and I don`t know why . I have change the Ignition switch , starter relay , coil is now a new MSD SS , Distributor is now a Summit RTR...

I made the Ignition Finger from the Distributor to show of my 1. cylinder mark and but the cap back on the Distributor. The wires in the correct sequenz on the cap. The 3 wires from the Distributor, Red to Coil + , orange to Coil - and the black on ground. I but also the Tach cable on Coil - and...

Step #10 I have made but there must be a 12V Power supply for the Ignition Distributor and Coil or not ? Was it possible to say with the place where the vacuum unit be how the RTR Distributor are installed right or wrong ? When the Distributor are installed wrong the engine not start and than...

I have buyed the RTR Distributor from Summit what IQ52 have said. How this RTR Distributor / Coil System get 12V ? I have installed the RTR Distributor and the Coil but I miss the 12V for the System. Did I have to but the 12V on the Coil and which 12V could I take

Did someone know more about or drive the Firecore RTR Distributor ? MSD are not so good as I was meaning. I don't buy MSD again.

Thx IQ52 for this awsome List and help. Which Cylinderheads you are prefer ? Alu or Iron ? X Heads or ??? Iknow the Edelbrock Alu Cylinderheads but there will be for sure more geat manufacturer as Edel. What about RHS Indy X-Heads for the 360cui ? This Heads are good ? Which one you could...

When I say made a 500 Horsepower 360cui for Street/Strip but no Stroker engine , was this realistic ? My Car have at time : Stock 727 Transmission with Stock Converter. 3,55 sure grip rear axle Holley 650 cfm Double Pump Carb Weiand dual plane intakte manifold MSD Street Fire Ignition Box...

My Stock Distributor are killed and now I want to Upgrade with Ooher Parts inside to get high Performance Distributior. My Ignition Setup are : MSD Street Fire Ignition Box MSD Blaster SS Coil 8,5 MSD Superconductor sparke wires What for Ignition Module for Distributor could you recommend...

Hi I have a 1972 360cui Engine in my 1974 Fish. What for Parts I must taken for maximum Street/Strip Performance ? What for Parts could you recommend and how mich i could get from this Engine without Stroke ?

Hi at all My 74` Barracuda 360cui with MSD 6200 Ignition Box and new MSD Blaster SS Coil don`t want start . The Spark Plugs are without fire and at the Blaster SS Coil are no energie . The wiring are all ok , also the Starter Relay . I check something with the Multimeter but found nothing . I...

Hi I need for my 1974 Barracuda a 3 speed wiper switch and a 3 speed wiper motor both in good shape . I need the Parts to get the Austrian vehicle License so they are very important for me . Shipping to Austria (Europe) I realy please for help

I need it too because I need this to get the Austrian Vehicle License so this Parts are very important for me . Did you also shipping to Austria (Europe) ?

Hi everyone I search for my 1974 Barracuda a functional Rallye Speedometer Gauge in good shape . Search about this Gauge over a month without success so i hope that one of you could help me to find one or have one for me . Maybe someone had an rare Km/h Rallye Speedometer for the Barracuda...

Hi I search for wheels reports for the size 15x8 , it`s for my 1974 Cuda where have 15x8" Weld Draglites . I need it for the Austrian authorities , they want a Datasheet for the Austrian Car Titles where I have to make . Will everyone thx a lot for help .

Thank you all for help me . I have found that Link http://www.440magnum.com/mopars/2011/december/1974-plymouth-barracuda.shtml and i also found on Youtoube Videos http://www.youtube.com/watch?v=Q7skO1oxlp4 http://www.youtube.com/watch?v=L_osejjaYwY&list=UUvS-QqJmy-oWxczGkbu09wg&index=19 I...

Hi everybody My Dash Vents / Dash Air outlet`s from my 74`barracuda are broken and i need some where will be ok and looking good . i hope someone have one or could help me . greetings from Austria / Europe

And what are with the dashboard air outlet`s / dash vents ??? My Dash Vents are broken and i need some where will be ok ( must not be new one only ok ) .