Search results for query: *

I have a couple of patch sections to replace on my roof skin, towards the lap seam with quarter on driver and passenger side. Long shot, but I know a few people have swapped out roof skins recently. Figured I would see if anyone would cut and sell me sections from your scrap parts. It doesn't...

Working on drivers pillar. I got it into place where it needs to be for glass/trim and aligned with the holes in the cowl side panel. It however leaves about .5" of space between the flat section of upper cowl/firewall/top of a pillar. I was working on clamping the replacement cowl down and...

WTB

Working on my 71 and repairing a piece of the back flange. I note the rear flange on the package tray which spot welds to the upper trunk filler/dutchman panel has various large and small holes in it. Given that it welds behind the dutchman what are these holes used for? These appear to be factory.

Anyone have a decent set of 71 clip/screw cowl screen covers? It'll be a couple years until I need a nice set, but I am currently mocking up the cowl before I install it. The version I have is screw on, but my factory version is clip and screw. I've used transfer paper to transfer and drill...

I've been working on installing a new filler panel. I noticed that it seems to sit proud of the quarter panel by 1/4 or 1/8 or so. I've not installed it yet but the quarters have not moved(on purpose) from the old dutchman. Wondering if I should slightly jack up the quarters though to make it...

I'm going through and tramming out all my measurements. It is my understanding I need to setup points x, located at the gauge hole areas in center of car. This measurement is 6" to datum, which could be the floor if exactly 6". Then for example point d at rear of frame rail would be 18.25...

I was initially planning on swapping the front and rear IRS, and a NAG-1 into my 71 E-body. I've since decided to stay with original suspension, and put in a modern hemi and a manual transmission. I've been looking at the Tremec t56's and it looks like a substantial amount of cutting of the...

Hoping someone may be able to measure either the front and back windshield channels for me, or the size of the front and rear windshield itself. Maybe length/width and x measuremnt. I had a badly cracked front windshield which I threw away during a move, and want to make sure fitment is...

Wanted

Looks like they are available, but are on back order. Curious if anyone knows when they are supposed to be really available, or how the quality is?

Hi all working on my 71, and can't seem to locate my drivers pillar where I had all my measurements on. Can someone measure the distance across rom a driver to passenger a pillar at the top and bottom? A measurement in the center of the windshield from top of channel to channel on upper cowl...

Working through some rust repair on my 71. I don't intend to relead this seam. Through research I've discovered that the suggested action is to weld the seam solid, then come in with a metal filler over the top. It gets welded solid, and then light coats of filler. I was curious as to if...

Entire Suspension/Drivetrain for sale from 1971 Dodge Challenger RT. Front: Upper Control arms Disc Brakes-knuckles, disc, pads, dust shields,bearings, flex lines, hard lines etc. complete sway bar-mounting brackets and everything to completely install Torsion bars, clips, boots Shocks (2) Strut...

Entire Suspension/Drivetrain for sale from 1971 Dodge Challenger RT. Front: Upper Control arms Disc Brakes-knuckles, disc, pads, dust shields,bearings, flex lines, hard lines etc. complete sway bar-mounting brackets and everything to completely install Torsion bars, clips, boots Shocks (2)...

Entire Suspension/Drivetrain for sale from 1971 Dodge Challenger RT. Front: Upper Control arms Disc Brakes-knuckles, disc, pads, dust shields,bearings, flex lines, hard lines etc. complete sway bar-mounting brackets and everything to completely install Torsion bars, clips, boots Shocks (2)...

Looking for 1971 Grille. Front and rear window trim 70-71 Dodge Challenger (doesn't matter condition as long as it is pretty straight.) It will be used for panel replacement mockup since I noticed the other day I don't have trim for either window. 1971 Challenger Trunk/Qtr Molding 1971...

Have the 4 3/4" head bolts loosened up so I can slightly move the brackets. I am having trouble getting the bolts all of the way out. I've tried ratchets, as well as an impact. My thought is that there is likely a u nut on the back side, in the frame rail that is broken. Thus the bolt just...

Not interested in leading the roof to quarter seam. It will be welded. Have researched two options, the first is to weld it solid, finish it with grinder, use weld through primer, bridge it with metal and then weld that solid. Followed by a little filler. Second option, cut that joint out...

Just curious as to what books I should pickup to help me? I know I need some kind of book that lists hardware sizes/types, and one that details correct placement of emblems. Any suggestions? Thanks