Search results for query: *

15 X 7 Magnum 500 wheel. 4.5" bolt pattern in excellent condition, date code 10/01/81, JJ Wheel made in USA. In excellent condition, used as spare wheel with tire. The tire is a Goodyear Eagle GTII. Tire looks like new, DOT date code 3105, used as a spare tire. $170. Located in northern, NJ.

Hi, I have a 1970 Challenger. The heat-A/C blower motor isn't working. My mechanic checked it out and it's the motor that isn't good. Are there companies that would rebuilt the blower motor from my car?

Hi, I've replaced the positive battery cable with a reproduction one for my 1970 Challenger 318. I want to make sure I have the red and black pigtail wires connected to the correct locations on the small square (solenoid?) on the fender well just to the right of the battery. Could someone post a...

Hi, Is a 1970 Challenger trunk lid the same as a 1974 trunk lid?

Hi, I'm replacing the starter on my 1970 Challenger 318. While I'm at it I'll replace the incorrect cable that isn't in the best of shape, with a reproduction positive battery cable. The cable came with a black plastic strap 4 5/8" long. It looks like it is designed to loop around the 2 cables...

Hi, For an 8 3/4 center section, 3.55 sure grip, 741 case, small yoke and snubbrd included and turns smoothly, would $750 be a fair price?

Hi, There is a guy selling an 8 3/4 center section, 741case, 3.23 gears, non sire-grip for a fair price. It's the gear ratio I want. Can I convert it to a sure-grip? If so, is it relatively easy? Or would it better getting a sure grip right off the bat?

I have a lead on an 8 3/4 rear end housing in good shape without the hard brake lines. Are the hard brake lines on a 7 1/4 E-body housing the same as the brake lines on an 8 3/4 ?

Can the driveshaft with the 71/4 be us when switching to an 8 3/4? Or will a different length length driveshaft ben needed?

2 BF Goodrich Radial T/A tires, P225/60R15. Like new, never used. One tire was was mounted on a rim briefly. Located in Clifton, NJ 07013. $225

Hi, I have a 1970 Challenger that I would like to get a later Mopar space saver spare tire for. I read previously that some years of the Dodge Caravan minivan have a space saver spare that has the correct bolt pattern and center bore (hole) that would fit. Would anybody know what years of...

My 1970 Challenger originally had a green interior and along the way it was painted black. I'm going to repaint the outside of the ash tray door green. What is the finish on the interior of the ash tray door supposed to be? Green and natural metal finish? The inside of the ash tray was painted...

Hi, This probably applies to all E-bodies. I removed the ash tray door easily. On the ash tray housing itself there are 3 screws, 2 on the top and one on the bottom. I removed those and the wire to the heating coil is unplugged. The housing seems to want to come out but it seems like there is...

Hi, How would I remove the bulb sockets on the under side of the tail light housing? I tried turning with no luck and didn't want to force it.

How do do remove the horn button from a 1970 standard steering wheel?

Large indoor car show, Feb 18th and 19th, 2023, Harrisburg, PA. motoramaevents.com

I'm planning on installing an 8-3/4 rear end in my 1970 Challenger in place of the 7-1/4 . Can I use the same drive shaft?

On 1970 Challengers with green interiors, I've seen the standard 3 spoke steering wheel spokes and the horn button either green or black. Are both versions correct?

Hi, There are two flat raised areas at each corner of the trunk lid with holes in the center where it looks like round rubber bumpers show go, but on my car they are not there. Instead they are on each end of the tail panel. I've seen a few picture of 1970 Challengers with the rubber stops on...

Does the A01 light group have its own wiring harness? Can an A01 light group package be retrofitted to a non A01 Challenger. If so, would you have to get the complete setup from a donor car?