Search results for query: *

Hello everyone, I had my Challenger out for a drive today on a nice 70 degree day, Like always, the temp gauge reads on the low end of the non-rally gauge. When I got home, I checked it with an Infared thermometer, it read 170 degrees. I checked the rad, thermostat and upper and lower hoses...

I need help with a frustrating issue. My Retro Sound radio has static as if it is cutting out with the engine running. No issue with the engine off. No issue when streaming thru Bluetooth. I added another ground to the head unit, but no better. Changed dist. Cap and rotor too. Even ran a...

I need advice. Only the rear passenger drum locks up after a few miles (smokes comes off). I have adjusted the shoes, but the only way to get the brake cylinder to compress is to open the bleeder. I have bled it over and over, the cylinder has been replaced twice, flex line over axle replaced...

I am looking for the sheet metal piece that covers the gap between the grill and rad support. Need to be able to ship to So Cal Thanks, please p.m. me

Greetings Friends, I have a dilemma; my passenger rear drum will lock up and actually keep the car from rolling. The first time I changed the wheel cylinder, thinking it would not retract correctly. It is still having issues, where there is smoke off the wheel. I checked the temp. and it was...

I need a drivers side rear regulator for a 71 Challenger. Needs to have a smooth movement and not slip when pressure is applied. Please PM me. Don’t expect perfect, but better than mine which has a stripped tooth Thanks

i installed a SSBC front disc kit a few years ago on my 71 power drum Challenger. I was never happy and after having a shop upgraded it to a dual diaphragm booster and a Willwood master, it still would not lock up the brakes in a panic stop. I finally broke down and ordered a system off E-bay...

I saw this at Lowe’s, screams Sublime Green, even the tire matches

Looking for feedback on anyone who has used the CPP Front brake kits. I have SSBC on it now and not impressed with the stopping power. I have a dual diaphragm booster and Willwood master. Engine puts out 16” of vacuum. Their kit looks like the factory sliding single piston design and uses...

Has anyone replaced their top themselves? Mine is showing it’s age, and I want to replace it along with a glass window. Is this something I should pay a pro to do?

Hello friends My 71 small block Stroker is having issues. Weak spark at idle, currently running factory electronic ignition with a chrome ECU. Frying coils and ecu every few months. I need a good reliable combination. Looked at MSD, FBO and Rev-n-ator systems. Who has a success story? Prefer to...

i have a sound in my passenger side of engine that sounds rocks rattling. I rebuilt and replaced everything except heads. I am now thinking valve spring issue. They are Edelbrock heads, with adjustable rockers. I have tightened, Loosened the lash, but it sounds awful below 1,200 rpms. But will...

how can you tell if the torque converter is failing? when I start my car, I have a rattling noise until the rpms get above 1,200. I just rebuilt the motor because it was making this noise thinking it was the motor, but it is still there. When I shift to drive, the rpms drop to about 500, then go...

I am pulling my 70 340 block because it spun a rod bearing. I am thinking about going to a stroker kit. I am looking at two options; 415 cu in 4.070 bore x 4" stroke, or a 371 cu in, 4.070 bore with a 3.58" stroke. Do either of these set ups require relief to the block, and what is the biggest...

Hello friends, I have a 71 Challenger convertible, I am missing the track that goes on the back of the rear seat to hold the front of the boot. Does anyone have a picture of it, and where do I get one.

71 Challenger with a 1969 340 and a 727 trans. When I start it it rattles and shakes when cold below 1,500 rpm. Pulled each spark plug wire, but can’t pinpoint which cylinder. Approx 3,500 since it was rebuilt, aluminum heads, adjustable rockers, cast iron exhaust manifolds. No exhaust leaks...

i found this site, it list every show, cruise night and weekly gathering in SO Cal thru end of September. It has flyers for most events: SoCalCarCulture.com

I am looking for a recommendation on valve cover gaskets. I have a SB with aluminum heads and cast aluminum valve covers. I am looking for a high quality gaskets that I can reuse with out goobs of silicone to prevent annoying leaks. Any recommendations?