Search results for query: *

I have a blown rear shock on my Challenger, and have a set of Monroe 58577 shocks lying around. I know these are for a C-body but I wondering if anyone has used them and to what effect?

I'm thinking of using an OD I have in place of the 4spd in my Challenger. Anyone done this? Will all the linkage transfer from the 4spd?

When driving my stock power steering Challenger the steering can get pretty twitchy especially when switching from one of my modern car. My question is for someone using the a fast ratio steering and idler arms, does it make it feel firmer?

Hey all, anyone the NC Traid area have a flywheel I can use to test run my motor? It doesn't have to be in good shape, it just has to have a good ring gear. The motor is on an engine stand and I need it to use the starter. It's going in a automatic so need a flywheel otherwise.

I took my car out today to wash and when I tried to close the window it wouldn't go up. Upon closer inspection I noticed that both the front guides had come loose. I was trying to reattached them but can't get the stud to come out enough on the top guide to fasten the nut. Also I do not how all...

Does anyone know of a source of metal bezels for the square 73-74 E body clutch pedals pads?

Hey I didn't know where the post this. I'm trying to install a windshield washer kit. Can someone please post pictures of their nozzles installed, because I'm having trouble determining the orientation on my hood. It looks like either this car did not come with it or is this is the repo Hood...

Anyone have issues with the OEM brand of replacement gauges. I bought a gas gauge tested it and it seemed to work then when I installed it it just stopped working. The other gauges are working fine. I know the sending unit is tested fine. The old gas gauge was working just fine but the needle...

Using a heat gun to restore faded vinyl panels, I've seen people do it on YouTube. Anyone here try it?

So I took out the gauge out of my Ralley cluster because the gauge works but the needle wasn't moving correctly. While removing it the needle fell out! Anyone ever mess with these, and knows how the needle is supposed to mount in there? It's not obvious by just looking at it. Seems like I'm...

Am I correct in assuming that all '66 and up 23 spline 4spd main shafts are interchangeable? Can a old style syncro rings just be interchanged with a newer style or is there more to it? I'm trying to swap out the guts of a 4spd out of a 68 Roadrunner that has a larger input shaft bearing...

Need a A833 trans for an E-body 23 spine input shaft in good shape preferably in NC or southern VA

Could someone please pist pictures of this harness installed? Thanks

Okay I have a restored Challenger with completely new wiring. I'm trying to figure out why the brake lights aren't working. The flashers and the turn signals both work I tested the on the brake pedal switch and that tested good and there is a pink wire and white wire going to the switch. The...

Is this empty connector on the firewall for the reverse light harness?

I just bought a 73 Challenger with 3spd wipers. The wipers work, but they don't go back to park? What should I be looking for? The harness is new, but the switch and the motor not.

I just bought this today, could someone post a picture of one installed so I know how it goes? Thanks

I'm trying to replace the shift boot and I'm having trouble getting the handle out of the shifter. I've used shims with PB Blaster and I can't even get a .08 shim to go in a 1/2". Anyone have any tricks or suggestions?

I need a 3 speed motor for my Challenger, and places like Rockauto only list a 2 speed. I did a lot of searching but couldn't find much, so I thought I'd ask. Is one from another car that would work? What about this one Cardone Wiper Motor - Domestic Reman 40-370: Advance Auto Parts

Hey all I just bought a 73 Challenger Rallye 340., and not sure about the seats could you please identify if came the car and if not what they did come out of. I want to make sure I the right replacement back panels for them. Also the there's a supression spring that's mounted on the top of one...