Hey guys, if anyone can help out I would appreciate it very much. I'm struggling with a Thermoquad. I have a 1971 on a 340. I have had several of these in the past and never had any problems with them. I sent this one off and had it restored about 5 years ago. I ran it on the engine test...
Hey all. I'm wondering if anyone knows where I could get a couple of the steel tabs that hold the carpet trim to the bottom of the door panel. I have attached a picture of the one that is broken. Thanks guys.
Hey guys, I have my car back on the road but it has no power steering. I took the pump apart and resealed it and I think it is pumping fluid as after the first fill I started the engine and the reservoir went to about 1/2 quart low and it squealing like a steering pump does when low on fluid. I...
Hello, I am finishing up the details of installing my shaker hood. I ordered new brackets to support the base plate. I have the two longer brackets that attach under the front of the base plate to the heads. However i got these two smaller L shaped brackets that I cannot figure where they go...
Hey guys, when I got my car the engine was completely disassembled and original parts were missing. I found a correct intake manifold and Thermoquad carb. I had the carb rebuilt and it runs great without the choke hooked up. My problem is when I hook up the choke stove linkage to the choke...
Hi guys, I finally got my car running. I installed the engine and transmission about 2 years ago. Now I have it running but the clutch doesn't seem to be working. I have the free play set correctly. I have the rear axle on jack stands. I start the engine in neutral and I cannot shift to any...
Hello, I'm back. One more minor detail. I installed the new engine wire harness. There are three wires to the alternator. Two wires with spade connectors, one blue with a tracer and the other is green. On the alternator both of these terminals have the same stamp or marking. Does it matter...
I am installing electronic ignition on 1971 340 Challenger. I have a new YEAR 1 electronic ignition engine harness. This harness has a 5 pin connector with 5 wires in it. I pickup an ignition module at the local Auto Value. It only has 4 of the 5 pin locations populated. I see in the...
I'm looking for some guidance. The car was apart when I bought it so I'm not sure where some wires connect. I do have a wiring diagram but I am converting it to electronic ignition and some wires do not match. I have "most" of the engine wiring harness connected. However I'm a little...
Hello again, I just opened my new rally dash harness and I am comparing it to the original. Where the park brake switch wire comes out of the harness there are two green wires that go into a single connector. I don't think it connected to anything on my car as I did not mark it with tape when...
Hello, I replaced my drivers side front floor pan and neglected to drill the headlight dimmer switch install holes in the new floor pan. Does anyone have these dimensions or a picture that will get me close? it is a '71 Challenger.
Thanks guys.
Hello, I posted this in the heater section earlier, thought I might get some replies on here. I am replacing my heater switch panel bezel but I don't know how the knobs come off of the levers? Do just the knobs come off or does the longer plastic also need to be pulled off the levers? Thanks.
Hey guys, I am replacing my heater control bezel because the original has holes drilled in it for a switch and an oil pressure gauge. I'm struggling with removing the knobs from the levers so I can pull the levers out. How do the knobs come off of the levers?
Does anyone have a picture of where the rear license plate wire and grommet pass through the trunk floor? I am installing new wire harnesses and I just realized that there is no hole in the new trunk floor. Thanks.
Hey guys, I am installing new exhaust hangers and exhaust shields on a 71 Challenger. The rubber slot is only open on one end. My question is, does this slot go towards the front or rear of the car? Thanks.
Good morning all, This is a 71 340, do I need a fuel return line or can I get by with only the supply line? The car was apart when I purchased it so I don't know if the return was connected or not. By the looks of it I don't think it was. I don't even know what it should connect to. I am...
I saw on another thread a wiper motor restored by Moparleo. Does anyone have his contact info or another restoration shop they would recommend? Thank you.
OK, here is my story, I have been a Challenger guy most of my life. It all started in the early seventies when I got a model (assembly required) for Christmas. It was the Sox & Martin Challenger. Some of you older guys may remember it. As I put that plastic model together I couldn't help...