1970 E-body steering column for manual steering and floor shift (stick or automatic). Will fit '70-'74, but is correct for 1970. Dated 10-01-1969.
Comes with the Rim Blow crush can ($140 new by itself).
Ignition switch connector was cut.
$205 plus shipping from 62450
10" rear brake backing plates removed from a big bolt pattern 8 3/4 rear end. Most of the hardware is still present, although new hardware kits are readily available, cheap, and recommended. Check out RockAuto part numbers H7129 ($5.10), H2528 ($6.08), and H2529 ($6.89).
Shoes are junk and will...
Removed from a 1970 B-body 8 3/4 rear end (big bolt pattern). They come with all the hardware shown in the pictures, although I'll probably discard the shoes before shipping.
$120 shipped to the lower 48
11 x 2.5" front drum brakes. Removed from a running/driving 1970 Plymouth GTX. Includes drums, hubs, backing plates, and hardware shown. All studs are RH. Spindles not included.
Location: Olney, IL 62450
$130 plus shipping
VIN - 0B433633 (came from a 1970 'Cuda per the guru, Mr. Alaskan_TA)
Casting date - 3/5/1970
I don't know the history of it, but it's been kept in storage with heavy grease all over the machined surfaces. It has not been magnafluxed.
Looks like it's been bored 0.030" or 0.040" oversize. That's...
Not sure which forum section this fits in, but I'm checking to see if this 340 block's car is out there somewhere before I sell it.
VIN - 0B433633
Casting date - 3/5/1970
Looks like it's been bored 0.030" or 0.040" oversize. No main caps.
Bellhousing (clutch cover) off of an NV4500 5-speed transmission. Will fit Dodge small block bolt pattern (5.2, 5.9, 318, 360, etc.). Good shape. Comes with transmission hardware (the 4 big bolts).
$165 plus shipping from 62450
Used MSD ignition setup. Came off of a running car, but I did not hear it run for myself so I cannot guarantee the condition of any components. I believe everything was installed in 2015 and the car saw minimal mileage thereafter. Owner wanted to go back to a factory look with stock electronic...
Aftermarket harness for electronic ignition box. Will work on 4-pin or 5-pin boxes. 46" total length.
$18 shipped via padded flat-rate envelope, PayPal fees included
Seen over at Mopar Connection Magazine. They're still out there...
https://moparconnectionmagazine.com/finders-keepers-1970-plymouth-aar-cuda-emerges-from-30-year-slumber/
2-1/2" Percy's Seal-4-Good collector gaskets. These gaskets are made from dead soft aluminum, so they're not only darn near blow-proof, but they're reusable, too. New, never used. Still in the original packaging.
$16 shipped to the lower 48. Prefer PayPal.
Looking to trade for a 12v or 24v Cummins engine (or complete parts truck). Depending on the deal, I may be able to throw in some cash as well. If 24v, prefer 1999 or older.
This transmission came out of a 440 Six Pack Superbird that was crushed. It has PK3410672 stamped on the rail and the VIN...
Edelbrock 8594 intake manifold bolts for big block (361,383,400,426 wedge,440) Chrysler. 12-point heads, washers included. Brand new, never opened.
$18 shipped to the lower 48
Bare 8.75 housing. 59-1/4" from outside to outside on the flanges. 43-1/2" from center to center on the spring perches. Nice starting point if you need one to narrow.
$125 plus shipping from 62450 or I can deliver to the Indianapolis swap meet on March 2.
11 x 2.5" rear brake backing plates. Removed from a 1973 Imperial 8 3/4, but should fit any 8 1/4, 8 3/4, 9 1/4, or Dana 9 3/4. Parking brake cables are still attached.
$50 plus shipping from 62450 or I can deliver to the Indianapolis swap meet on March 2.