I am electrically challenged but my mechanic is electrically savvy but we are stuck. I have Sniper with hyperspark distributor, hyperspark ignition box, and HSpark coil.(and Holley Efi tank/ in tank pump). Internally regulated, single wire alternator and Dakota digital dash resulting in mostly...
I have the mopar performance big block cast valve covers with a twist on hole and knock out spot on each. I am installing a m/e Wagner Pcv valve in one of the twist on holes. It needs 3/4” id. Does anyone know which grommet with that id also has big enough diameter to seal twist on tang...
I have TTI headers and am still trying to decide wire routing and boot angle. Not trying to duplicate original setup. I’ve looked at as many pics as can find. Looks like lots of people run them around front below headers vs running any over valve covers. I like cleaner look running under...
restored my heater box and installed. A gap exists between it and plastic defrost plenum that goes up to windshield. Is that gap normally open or was some sort of gasket used. Nothing was there when I took it apart but most of the old foam in heater box had disintegrated and disappeared...
since I am already spending more than I want on resto, who doesn’t, I am going to tackle restoring my steering wheel. I have the 70 3 black rubber spokes with silver inlay, plain horn cap. I will attempt duplicating the wood grain, at least the overall impressions of wood if not exact. I have...
how important are the plastic film moisture barriers inside Cuda door panels? Since panels are plastic do they really need protection like styles that have cloth or cardboard backings? I saw a thread somewhere how to make them and found a kit on web, just wanted opinions. Not concourse resto but...
I want to replace windshield and all side glass in my Cuda convertible. From research, seems most are happy with ECS and AMD. some say they source from same supplier.
What about Auto City Classic? I know they source from China also and they are cheaper but that worries me a bit. Anyone have...
I ordered blower motor for 70 Cuda non a/c. Obviously some big differences in looks but more importantly the shaft for cage is longer and holds further out from motor so it rubs on inside of housing. The cage I took out of it is plastic...is it even original? I have only seen one picture of...
i am putting a Holley sniper on edelbrock performer rpm on 440 in 70 Cuda and was wondering if anyone has this combo. I have no throttle cable, return spring, brackets or linkage. What stock or aftermarket parts did you use?
Does anyone know if injection molded rear interior panels for Cuda convertible are available? Seems like only vacuum formed available for verts.
Has anyone had their originals restored. Mine have a bunch of small holes drilled for aftermarket speakers ( and not uniformly done, so spraying them...
I called Dakota Digital and MH wiring that supplies harnesses to Year One and not getting any definitive answers. If you can shed light, thank you
I have non rallye dash in my 70 Cuda. Already have the VHX cluster from DD. I am replacing all 50 yr old wiring harnesses. My big question is...
70 Cuda...are bumper brackets body color or black? Mine have so many layers of paint and rust it is hard to tell.
I believe Hemi orange is correct 440 engine color but What about bell housing, 4 speed tranny, and driveshaft color? Getting close to paint time. Thanks
does anyone have correct measurements or diagram for location of pentastar on right fender. 70 cuda with gill lower rockers if it matters. Looks like most pics I see are centered between wheel opening and door, but seems like more variation in vertical placement between rocker and body line...
I am planning on running Sniper with EFI tank on the Cuda. I am guessing supply line can be O.E. style and routing, but where have you run return line? Not having car readily available, I can’t check to see if room for running return next to supply line. Could another OE metal supply line be...
I am considering installing RMS alterktion kit. Still pondering pros and cons but 1 big problem is that 15x7” rallye wheels with 4.25” backspacing exceed max 3.75” alterktion can handle. From more research, it appears Spacer that big is out of the question but adapter ring that actually keeps...
I am adding sport mirrors to 70 Cuda that had no passenger side mirror. LH side was not sport option either. I haven’t looked to see if LH holes line up ( mirrors shipped to body shop an hour away) but bigger question is placement of Passenger side. Do I just measure to LH side base and...
Anyone use a plastic repair kit successfully on dash bezels or door panels. This Eastwood kit caught my eye. I have some repairs to make and may buy a better bezel that still needs a bit of work on broken tabs.
Rigid Plastic Repair Kit Black