Got a variety of parts. I want to sell the whole lot. Here in Woodstock, GA
Heater core HVAC unit – like new.
8 Small block Keith Black Pistons .30 over Only 500 Miles
2 Side Windows (2 doors and 2 back seat)– frt door LH side is tinted. fair
Small block exhaust manifolds – very good...
On the ebay motors block! Plymouth: Barracuda CUDA
‘Cuda Video: 71 Cuda2.m2ts Video shows Gold engine. I just repainted it.
HEADS UP. It is a true 340 4speed CUDA car from the factory. Matching numbers except for the 360 engine. An era correct 340 block (with minor repairable crack) will...
1971 Plymouth Barracuda ‘CUDA $65K OBO
EBAY MOTORS: Plymouth: Barracuda CUDA
‘Cuda Video: 71 Cuda2.m2ts
More pics link: 1971 CUDA
It is a true 340 4speed CUDA car from the factory. IT HAS A 360. Matching numbers except for the engine. An era correct 340 block (with minor repairable crack)...
Hello gang,
This is kind of a spinoff from my other thread. "sputtering issue with new carb".
Holley 870 vac,: I jetted down to 78 primary/82 secondary from 82/82. Sputtering was better, but still did some.
Can I jet down further? How do I know if it's too lean?
Holley 670 vac: I jetted up...
Hello gang,
When diving the carb will sputter. I can cruise at any speed (40 to 80 mph) consistantly and out of the blue,,, it sputters for a split second and then is fine. It will do this at various times, but approximately every 45 seconds to a minute.
Here are the facts. Heads up ,, I'm a...
Hello Gang,
Got a '76 360 block. Fresh rebuild but the rear of the pan is leaking.
I just ordered a Milodon one-piece gasket from summit.
Can I put a little sealant in the corners?
Any recommendations are appreciated.
thanks,
rick
I'll keep short and to the point....
I bought the 3" Stainless Steel exhaust kit for my 71 Cuda, 340, 4 sp from Summit Racing. I polished the system to even more of a shine. :happy4: Prior to test fitting. :P
The system does "NOT" fit 4 speeds and "through valance" tailpipes.
The "X" portion...
Hey gang,
I have a leak with my new Summit Ceramic headers on the driver side. :angry1:
The gaskets that came with them were installed.
Recommendations would be greatly appreciated.
Thanks ,
rick
Does anyone have the lever that attaches the motor to the arm inside the cowl?
I also need one of the two sections of the wiper arm that holds the refill. Its about 4 inches long.
Thanks
Hello Everyone,
I have a 71 Cuda. The current dash is w/o A/C.
I would like some recommendations.I need to buy a new one or rebuild my current one.
I am installing Nostalgic Air. I would like to change to an A/C Dash pad.
I would need to buy the vents.
If I send it out to have it redone...
My cuda currently has non power steering.
I want to add powersteering. I do have a pump with pully sitting. Still have to get a gearbox.
Pressure hoses apparently are different.
How do I tell?
Any recommendations on where to get gearebox?
thanks,
rick
Hello gang,
I just had a 340 built (about 375 HP) 4 speed.
I'd like recommendations please.
Thanks! I really appreciate it. I'm crosseyed try to figure it out.
Hey gang,
I'm a newbie.
I just had my 340 rebuilt. It will be about 375 HP. It has an Edelbrock perfomer intake. 4 Speed tranny.
I'm thinking 650 Holley, doublepump, mechanical secondaries, electric choke.
I'd like some recommendations.
Thanks!