serious question, I'm looking for a great place to purchase a bullet proof transmission and torque converter for my 72 Cuda I'm running a 550 stroker wth 690 hp and I've destroyed 2 TCI garbage transmissions .
is there a reputable place I can call to get a good one? also has anyone ever heard of...
1972 Barracuda with an 8 3/4 rear end with 489 casting running 3.23 gears 727 Torqueflight auto trans. what would be the best gear ratio for this set up without taking away from my cruising on the weekends? this is not a drag car mostly cruising and show. But I would like to see a little more...
So I have a 1972 Barracuda with an 8 3/4 rear end with 489 casting running 3.23 gears just took it out for a drive about 40 miles and noticed that upon return to my home that the rear end is very hot so I shot it with a temperature gun and it's showing 168 degrees on the outside case is this...
I have been looking through some of the threads and I have come across some of the same questions as everyone else where does it go?
I have a 1972 Barracuda and I'm stumped on these wire locations and where they connect to.
first one is on the drivers side just below the gauge cluster right...
Hi I am installing a new neutral safety switch wiring harness on a 1972 barracuda that I did not remove I have everything hooked up except this wire can anyone please tell me where it hook to. it is a 340 engine with a 727 torqueflite automatic transmission.
Thank you !!!!
ok to start out I have a 1972 barracuda with a 440 engine it has a big mutha thumper cam 1.6 harland sharp roller rockers. 10:1 compression. I am running the MSD atomic efi setup with the MSD fuel pressure return system and high hp output fuel pump 625hp MSD blaster coil Taylor 409 Spiro pro...
I have a 1972 Cuda 440 that I am in the process of building and I'm down to the shaker hood
can someone with knowledge on how this all fits together please guide me on how it all works.
or point me in the direction of a web sight where I can find this info.
also if possible can you post photos...
I'm looking to sell a Comp Cams big motha thumpr camshaft part # 21-605-5 with a timing chain set along with some Valve springs part# 911-16 all still new never used PM me if you have any questions.there is nothing wrong with these parts I decided at the last min to go with a more aggressive setup.
looking to sell a few parts from a 1972 Cuda including complete front end suspension system( K-member) rotors bearings all......
heater motor $20
wiper motor $15
flex plate for 727 torque flight $20
distributor for 340 $ 50
I have a front grill that is broke on one end and two pieces from...
so I have a 1972 cuda 440 that I am in the process of building currently not in my possession 6 bolt pattern on crank, it has a 727 torqueflight Auto trans. but no flex plate my question is can someone please help me decipher the code on my block and tell me what year block it is if the crank is...
thank you,
I have a 1972 Cuda with a 440 swap (non factory intake) trying to install a shaker hood but
I am running into clearance issues.
I do not know the original Carb pad height for a stock 440 intake.
will it be better to go with an Edelbrock Performer RPM Manifold height: A-4.90"...
IN need of a 1972 thru 1974 grill for a 1972 Cuda or information on where I can get my hands on
one. any information will be greatly appreciated.
thank you
I'm new to the forum andI have a 1972 Barracuda that I am trying to restore. I am at the trunk area,
the lid was removed prior to my purchase and all I have is 1 torsion bar.
Can anyone tell me if I am supposed to have 1 or 2 torsion bars? also if you have pics showing the assembly it would be...