• Welcome to For E Bodies Only !

    We are a community of Plymouth Cuda and Dodge Challenger owners. Join now! Its Free!

Recent content by 73-Cudah2

  1. 73-Cudah2

    Heater core

    Thanks for the information. This will help.
  2. 73-Cudah2

    PDR on my 73 Cuda

    Ready to continue with PDR ( I know It needs painting just do want to grind off original paint just yet ) going to work wheel well area next.
  3. 73-Cudah2

    Heater core

    I am looking at replacing the heater core on my 73 Cuda not AC. In reading other posts about it is seems like 3 fan motor bolts 2 vent door connections and Fan Motor. Has anyone else replace one without AC? it that all there is? Also do you think replacing the air box parts are necessary if you...
  4. 73-Cudah2

    PDR on my 73 Cuda

    Sorry for the long pause! I will be starting up again now that winter is here again. I'll post the new progress on the panel. I'll have to take it a part again. Had fun driving it around this summer!
  5. 73-Cudah2

    1970 Baracuda Restomod Begins

    Great Job!
  6. 73-Cudah2

    1973 Cuda wiper motor not working

    After I re-cleaned the contacts (the inside contacts of the wires that contact to the motor) the wiper motor worked. Thank you all for the suggestions.
  7. 73-Cudah2

    1973 Cuda wiper motor not working

    Yes I did check the linage. I moved it by hand to make sure it was not stuck. It a new motor but I will scuff both ends who knows? thanks for the feed back.
  8. 73-Cudah2

    1973 Cuda wiper motor not working

    I had read some information on wiper motors and looks like my old one was dead. I checked the terminals from the battery shown on some posts. also noted if not grounded it will not work if issues were found there. I did ground from the battery to the ground strap on the wiper motor but still...
  9. 73-Cudah2

    1970 Baracuda Restomod Begins

    Nice Job! looking good!
  10. 73-Cudah2

    PDR on my 73 Cuda

    Here are the ones during PDR.Only working on the upper section above body line at this point. still need to but out lower indent. I am registered for Mopars in the park in Stillwater MN ( june 2,3,4) if you want to look at it more. Thanks for all the help and pointers on doing this.
  11. 73-Cudah2

    PDR on my 73 Cuda

    I have made some progress in pushing out the dent to start the PDR. it is working but slow process. Here are a few photos of the progress. I used the poll on a wall with 2x6 and 2x4s to reinforce when using the porta power on the dents inside the car. I also used the porta power inside the...
  12. 73-Cudah2

    PDR on my 73 Cuda

    I had to cut some of back plate that covers the headlight behind the head light plash shield. Used a steel rods and some custom rods to help push out the dents from behind. I also covered the ends of the tools I made with Gorilla tape to protect from any sharp edges. I had to replace the tape a...
  13. 73-Cudah2

    PDR on my 73 Cuda

    Here are 2 who are at least interested Lol. All that pounding.
  14. 73-Cudah2

    PDR on my 73 Cuda

    Still working on them. I will post more pictures on them before I sand and primer the header panel. also the progress on the quarter panel progress.
  15. 73-Cudah2

    PDR on my 73 Cuda

    Started working on PDR on the Cuda. Using it on the front right side of the header panel passenger side working out good. I have a few dents that the paint was missing so just using home made tools to push them back. I am using hydraulics push the lower quarter panel out then I will be using PDR...
Back
Top