• Welcome to For E Bodies Only !

    We are a community of Plymouth Cuda and Dodge Challenger owners. Join now! Its Free!

Recent content by slantfish

  1. slantfish

    FOR SALE 70 Challenger NON Rally non A/C heater controller.$30

    This is correct for a 70 Challenger, not a 70 Cuda.
  2. slantfish

    Floor prep/rust prevention before sound mat

    peel off all the old seam sealer, dig it out where you can. get as much rust off as you can, otherwise it can come back to haunt you. I used chassis saver over my entire floor pan to seal it up (extra tip from my body guy: let it flow into the seams and joints to help prevent future rusting from...
  3. slantfish

    Good deal or not?

    decent price for this project, it's tough to find any Cuda projects under $10k for the last couple years. a '74 360 is a great car too, rare low production #s.
  4. slantfish

    Deciding build sheet

    this is for a '70, enough codes may translate across the years, but not sure and it may be hit/miss. Mopar Fender Tag, VIN & Build Sheet Decoders
  5. slantfish

    Slant 6 Owners - group buy

    it's the engine harness. chose to go with M&H because they seem to have the most accurate harnesses
  6. slantfish

    Slant 6 Owners - group buy

    perfect. these will be for a '70 model year. learned on another forum that '70 and '71 are slightly different and have different part #s 3 follks have stepped up so far. no word yet from M&H, but with the craziness going on I'm not surprised.
  7. slantfish

    Slant 6 Owners - group buy

    no word from M&H yet, just bumping to the top for visibility in case anyone missed seeing it and wants in
  8. slantfish

    Ebody Ashtray Insert Installation

    or recover some of that investment by offering an install service. I'd pay $30-40 to have someone install it right and not bother buying the tools for a one off
  9. slantfish

    Any members near Montrose Colorado?

    it's a bit over a 5 hr drive from Denver, and that's going over the rocky mountains in the middle of winter (if it wasn't so far I'd do it, but it would be a day trip over, stay overnight and drive back the next day sort of thing)). best bet is a member in the Grand Junction area or eastern Utah.
  10. slantfish

    Slant 6 Owners - group buy

    Hi fellow slanters! I'm about to send my slant 6 engine harness to M&H for reproduction since they do not make one or have the pattern yet (because of this, I can get around YearOnes exclusivity for M&H harnesses this one time). it will take them 10-14 weeks before I even get an estimate for the...
  11. slantfish

    Gear Ratio fo 6 Cylinder

    either the 2.76 or 3.23 gears, I haven't seen any other factory combo with the slant. personally I would go with 3.55 gears. be aware that the 7 1/4 was pretty weak and a 318 could easily break one, so putting a 360 in front is a good recipe to kill the chunk early and parts for the 7.25 aren't...
  12. slantfish

    FOUND Challenger Slant 6 3spd Driveshaft

    47 1/8" total end to end (top of the u-joint castings) I also just found this that is MUCH better Driveshaft length in Engine, Transmission & Rear End based on the charts, should be 45.79" center to center on the u-joint caps.
  13. slantfish

    Missing vin tag

    your best bet might be ECS Automotive Concepts - Home or VIN Tags & Hull Plates Replacement - VIN Plate Manufacturer | Aluma Photo or Dodge id plate, VIN tags, Body plate - Identification Plates
Back
Top