• Welcome to For E Bodies Only !

    We are a community of Plymouth Cuda and Dodge Challenger owners. Join now! Its Free!

Search results for query: *

  • Users: LA390
  • Order by date
  1. L

    Hood Clearance

    That will be nice. However, I sold my "CUDA last week.
  2. L

    Hood Clearance

    That's true because the Torker intake is for square bore carbs. I have a Holley and a spacer for that engine. But the 318 that is still in the car has a factory 340 intake and a Thermoquad now. It runs well and I like the Thermoquad. The weather is finally getting nice and I took my 'cuda for a...
  3. L

    Starting my 1972 Challenger Rallye 416 4 speed 3.23 PS PB !!!

    Just my opinion but if you want to put the vinyl top trim pieces on you need the vinyl top, too.
  4. L

    New member

    Hi DFR360, I got the seats back from Weinmanns and they were a bit more expensive than I expected. $455 for the covers from Legendary and $424 with tax to have them installed. But they look SUPER. Just thought I would let you know for future reference. From what you told me, I think I will have...
  5. L

    New member

    I should have replied about this sooner. I did get the 318 running well eventually. The problem was a strange one. There was a hole in the bottom of the intake manifold where a pipe plug deteriorated. Who would have thought to look there? So I replaced the intake with a factory 1972 four barrel...
  6. L

    Hood Clearance

    From the photos that you sent it looks like I should have plenty of room without the 1" spacer at least. My situation with hood clearance is very similar to yours. I have a hood insulation pad that is taking up a little space but it wouldn't be a problem to remove that. I sure do appreciate your...
  7. L

    Hood Clearance

    OK. My drivers seat has splits in a few of the seams so I will get them both redone so they match. I have an appointment to bring them to the upholstery shop on January 4th. Weimann's Interiors in Delmont did such a nice job on my Demon's seats so that is where I am taking the "Cuda seats. I am...
  8. L

    Hood Clearance

    That would be great! Thanks. I finally received my seat covers from Legendary on Wednesday. They had been on back order since Sept.
  9. L

    Hood Clearance

    Hi Dfr3604cuda, Thanks for the reply. I would like to check it out and see your 'CUDA. Finleyville isn't far from Greensburg. Hopefully the covid thing will be over soon. Matt
  10. L

    Quality of original Factory Panel fitment on the "E"body cars.

    Interesting. You would think that the manufacturers would have gotten much better by now with panel fitment.
  11. L

    Hello E-Body enthusiasts!

    Sounds like you have plenty of work to do now. That 318 could be bored and stroked to a 390 if you wanted more get up. But most people would advise starting with a 340 or a 360 block since the cost would about the same.
  12. L

    Quality of original Factory Panel fitment on the "E"body cars.

    Dec. 9th 2019 was the day it was pulled out of the garage after 21 years hibernation.
  13. L

    Quality of original Factory Panel fitment on the "E"body cars.

    I didn't find the build sheet yet, but the fender tag is still in place.
  14. L

    Quality of original Factory Panel fitment on the "E"body cars.

    I think that it is factory original paint. It still shines decent.
  15. L

    New Barracuda owner

    1971 is the most favored year so some of us may want to see what you might sell in the future.
  16. L

    Quality of original Factory Panel fitment on the "E"body cars.

    Thanks. I added a couple of photos. So it could be a factory defect, then. My doors do sag slightly.
  17. L

    Quality of original Factory Panel fitment on the "E"body cars.

    the door gap is off at the bottom. Would the factory have left it like this?
  18. L

    Question about wheel size

    I run 15" x 8" with 3.75 back spacing on the rear of mine. The tire is a 275/60 R15. There is still room on the inside and the outside would be close if the suspension were about an inch and a half lower. So if your wheels have a 4 to 4.250 backspacing you should be good. I can't say anything...
Back
Top