Search results for query: *

While inspecting and messing around with one of my seat adjustment tracks it kinda fell apart. I checked the 1970 Service Manual for a breakdown diagram, no luck there. I want to put it back together properly and gain some knowledge. The roller bearing and a round bee-bee like bearing fell out...

So I picked up a really Nice set of Rally Barracuda Seats. I took the back off the passenger seat and discovered a build sheet for a BH Vert. Would be great to find the car and get it to the owner. Photo attached and here is the cars number BH27G0B2259495. Man I wish I could find mine 🌴

I have two sets in black and one in green. OEM in excellent condition. $175 a set plus shipping. 🌴

I will be at the 2025 Fall Fling and will have a Nice set of Ebody Bucket Seats for sale, complete with OEM Tracks. Also an Ebody Roll. BarHere are a few photos. DM me if you’re interested. 🌴

I will be at the 2025 Fall Fling in Van Nuys on 18 Oct. I be selling a Set of nice Ebody Bucket Seats (Seats complete with Tracks) and an Ebody Roll Bar to include other parts. I have attached some photos so anyone interested can PM me 🌴

I have a set of 340 exhaust manifolds that were thrown in on a car deal I made. Can anyone provide any info on them by the photos? 🏝

Hi, I purchased a set of Top Catwhisker door panel felts. I cannot seem to get them to fit on my door panels. Does anyone have any experience with Top Cat whiskers? And is there any tricks to the trade as far as mounting them? Any help would be appreciated. 🏝

Looking for a set of AHB rear sway bar frame mounts. Photo attached. I have read that the Firm Feel mounts are close but do not fit correctly. 🏝

Looking for the mounts that attach the Sway Bar To the K Frame. Attached photo identifies the exact parts circled in red.

Looking for 3 or 4 Upper Door Panel Clips for my 70 Barracuda, like the ones shown in the attached photos.

I have the rear seat covers from my 1970 Barracuda Convertible. They are in pretty good condition. Full disclosure: The material is very supple, two small tears on the middle of the lower seat cover that is hidden/covered when the top back seat is in place. The top seat has some stitching that...

I have a set of brackets that were given to me during when I acquired my 1970 Barracuda Vert. These parts may not be specific to 1970. Can anyone identify what they are? They appear to be mounting brackets, maybe frame/ suspension?

Hi all, anyone know where I can source a Master Cylinder Cap and Gasket for a 2229171 M/C. I see they are stamped #J1703 but it appears there are some different variances for different years. Does anyone know if any J1703 cap will properly seal on a 2229171 M/C? Any info would be much appreciated 🌴

Hi All, Trying to source 1970 Barracuda Convertible Rear Window Tack Strip Fasteners. There are 19 bolts that attach the Tack Strip that secures the Top and rear window to the trunk area. I understand some are T-bolts and the others are bolts with flange washers. Maybe they can be attached using...

New member switching over to Testoration thread. Bringing my 1970 Barracuda Convertible back to life. I have started with drive train. Replaced timing chain, water pump, freezer plugs, etc… pulled the transmission to replace pump seal and rear freezer plugs. The photo show a better way to remove...

Hi All, I actually installed my new Door Hinge Spring without removing the door or scratching the paint. I should patent this tool I made 😂. I took about an 18” 1/4” rod and notched it about 1/2” from the end. This notch held the spring in place. Then I bent the rod to slip in and hold the...

Hey all, I have a 1970 Barracuda and need the following parts: right rear wheel well trim and the interior chrome passenger door handle. I know they can be bought as a set, but trying to save on cost. Any help would be appreciated!

Hi All, I have the reproduction Belt Molding Kit for the top of the drivers door on my 1970 Barracuda Vert. How do you install them properly? With the insert pushed into the clip expanding the prongs they won't go into the holes. I don't want to push to hard and bend the molding. When I put the...

Hi E-Bodies, my name is Rob. I'm an Mopar guy who had a 1971 Barracuda in High School that I sadly sold prior to entering the Service. Since then life has got in the way, until last week when I was finally able to acquirer this 1970 Barracuda Convertible after three years of trying to buy this...