Search results for query: *

On my 70 AAR clone, there have been many patches made to the floor and the frame. It looks like both quarters have been replaced, the truck floor and the rear floor has been replaced. I found that the frame on the drivers side needs to be repaired. Can this be repaired by welding some plates of...

I have a two speed wiper motor that I need repaired. I have seen many posts on this site with names of people that repair wiper motors but no contact information. Does anbyone have any business cards or contact info for these companies? Thanks

My wipers on my two speed wiper motor does not park correctly. I read many of the posts and watched the Chrysler master tech video. I grounded the L terminal and put power to the P1 terminal. The wipers go to the park position. The jumper wire got pretty hot from the momentary contact to the...

The rear bolts on my front bumper are rusted and I can't remove them despite heat and penetrating oil. I plan on cutting the heads off the bolts. What is the best way to remove the heads of the bolts? A grinding wheel or a cutting wheel? Or should I get a cutting torch? Thanks.

I have a 70 Barracuda. I'm having problems finding original fenders for a 70. I found a set of original 71 fenders. Will the 71 fenders fit on my 70? Are the mounting points the same? The alternative is to buy aftermarket fenders, which I rather not do. Thanks

I just removed the carpet and I was looking at the spring on the shifter. Is this spring installed correctly? It looks a little odd. Also, does the plastic bushing look like its installed correctly. It's secured with a piece of wire. I looked at a couple of diagrams and I couldn't tell the...

Did a 70 Barracuda have seat belt retractors? I had a 70 Barracuda and I don't remember it having retractors. The photo is the passenger side. The seat doesn't slide back and forth properly because of the retractors. The side cover for the seat does not fit properly because it hits the...

I thought this group would get a kick out of this. This is a way to recycle your spark plugs. I saw this at the outlet stores in Las Vegas.

I want to convert from headers, back to stock exhaust manifolds because I don't like the noise, heat, and scraping on the ground when I enter a driveway. I've been looking for manifolds for a 340. They are impossible to find or they are very expensive. Will manifolds from a 360 flow as well or...

Does anyone have experience using urethane adhesive to install a rear window? I got a couple of quotes for over $200, just to glue the window in. The glass is already out of the car. I checked the internet, all I could find was the installation with butyl tape. May be I need to widen the search...

What is everyone doing with stripped sheet metal holes? The easiest thing is to get a larger screw. But what do you do with the holes for the sil plates or other areas that are visible? I tried JB weld Steelstik, that didn't work. Should I use the liquid epoxy or thread lock? Thanks

Has anyone used these seat stop? I bought these from Classic Industries. When installed the seat back won't latch. Are these supposed to be cut to fit and then shim up the latch? Where can I get the original style stops? Thanks

I have a 70 Barracuda that came from the east coast. For the most part the body does not have a lot of rust. I don't know why but they painted over the rust instead of prepping and then painting the car. Can the rust spots be repaired? Or would it be worth it to replace the fender. I know...

On by 70 Barracuda, the sail panels is falling off. The driver side is missing. How is the top of the panel secured? the front and rear of the panel is covered by the metal moldings and the bottom is under the plastic rear panel. the top is not secured to anything. Is something missing? Thanks.

I removed the rear window glass to repair some rust holes. I'm installing new trim clips. Does it matter where the spacer clips (I think that's what it's called) go? The old clips were missing. Also, is adhesive used to reinstall the rear glass or is butyl tape used? I heard this tape is...

Does anyone know if the internal parts of a column shift steering column is the same as a floor shift steering column. I have a floor shift column. There are some parts missing. I found a column shift column. I need the lock plate. For some reason, it's missing. Thanks

I have a 340 engine. I'm trying to determine what year the engine is. I located the stamped info at the base of the head on the driver's side. I have looked on different threads that explain the stampings. I don't understand what they mean about a 10,000 day calendar, when they talk about the...

I plan on converting my 70 Barracuda to power steering, First, is there a difference between a big block pump and a small block pump? Second, will a steering box from a A or B body fit an E body? Thanks

Are the stock exhaust manifolds the same for all years the 340 was built? Also, are the manifold specific to the body style (B body vs etc)? Are the 318 or 360 manifolds the same as a 340? Thanks

On my 70 Barracuda with manual steering, I noticed if you pull up on the steering wheel, there is a 1/2 gap between the steering column and the crush can. I posted this problem before. Some people responded that the shaft may have collapsed, like it's supposed to. The other day I noticed that...