This is a decent ebody crush can dates 9-69. It has been beadblasted primed and painted the low gloss black. It has the horn wire and is very clean. $75.00 and I will include FREE SHIPPING
Ya, me too. I think I had the key in the on position and as soon as I saw smoke and selled wire I shut the key off and it all stopped. Those starter terminals are very close to the block. I put one in my demon and I used that terminal stud relocation kit. I should have known better and I had...
So far I have had my 7 years old optima battery load tested and it dropped to 11 volts and it was at 100% charged. I am going to replace it for starters. I also think I may have an issue with the mini starter studs touching my block which has a nice ground wire coming off the negative side at...
I am searching for my power probe now. But I failed to mention I had replaced my ignition key cylinder a couple weeks ago and the car started fine after install. This car has been garaged and not run much in the past 7 years. All I did was change the starter to a Mopar high torque mini...
Hi, Just installed a new Mopar mini high torques starter and installed a new starter solinoid. Nothing happens except some clicks at the solinoid switch. Battery is at 100% and at 14 volts. While standing in front of the battery side fender I all of a sudden smelled wire burning and pulled...
Hi Looking for a setup missing from my column. It is the round lock out plate that also includes the locking lever with the spring for my 70 challenger steering column which is a floor shift car. The plate is a disc with fingers all around that the lever locks into when the key is off and...
The screws for the center are pan head as shown in the document and there are 4 of them. The outer screws are phillips oval head which has a tapered underside on the head to fit the tapered topside of the speaker grille on the two small outer grilles.
I bought very nice aftermarket speakers which have a small magnet and like 40 watts of power and they fit perfectly. I will take a picture and place it he later today. I also bought a very nice center speaker. Watch for my post.
No. These are the screws that the actual speakers mount with. I am looking for the screws that go thru the speaker grills down into a bracket which is also screwed to the bottom of the dash pad frame from underneath. Then the two black screws go down thru the grille into the bracket below and...
Can you take a photo of the two screws that hold the grille in so I can see what type they are? Now that you have them out of your dash pad? I was also wooking to find out about the screws under the dash pad that hold the backup plate in place. Need pictures so I can chase mine.
Hi, Is there a chance I can get somebody to remove one of the screws in their outer small dash bezels in a 3 speaker dash and post a picture of it on here. I am missing mine and I do not know what type these are. The backing plate that goes under the dash pad has two holes in thin sheetmetal...
Brand new pair of heavy guage front torque boxes for a 70-74 ebody/ New, never installed. $100 plus shipping. I have had these for a long time so I do not know who made them but they are very heavy duty and brand new.
Dash is already out and on a stand all assembled. I need to get at the two backup brackets to install the two outer speakers. Can I get at the without taking out all the bezels cluster ect. The two brackets have top get screwed on from underneath the dash frame
Is it possible to remove my new 3 speaker dash pad while on a completed stand to install the two outer speaker brackets that go from underneath with screws?? I forgot to install them and the dash is done and all mounted to the frame??
Refurbished dual snorkel air cleaner. Correct 1970 version. It has a brand new repro 383 pie plate callout. The pie plate color is hemi orange. The air cleaner was media blasted, primed and painted with semi gloss black interior and wrinkle finish exterior. It is in excellent condition...
I took mine to Carlisle and put FREE on them. I had two sets and two people were very happy to get them. They even offered me money to help pay the gas to get them there. Better than shipping them to China, as they were MADE in AMERICA.....