• Welcome to For E Bodies Only !

    We are a community of Plymouth Cuda and Dodge Challenger owners. Join now! Its Free!

Adam's latest activity

  • Adam
    Adam reacted to money pit's post in the thread Driver's Door Won't Open from the Outside with
    Like
    Like
    .
    The door would open but was very difficult to open. I would have to put the window down and pull on the door. I tried the rod both ways...
  • Adam
    Adam replied to the thread Oil Pressure Low.
    I would do #2 first, I think it’s the most likely problem and may save you some work. I believe the pick up threads into the block, no...
  • Adam
    Adam reacted to oneof52's post in the thread Oil Pressure Low with
    Like
    Like
    .
    Ok, so my next steps are the following; 1- Remove the oil cooler and put a fresh filter on the actual pump 2- Remove the distributor...
  • Adam
    Adam reacted to Cuda416's post in the thread '70 Vert - waited long enough... with
    Like
    Like
    .
    It's my own design.
  • Adam
    Adam replied to the thread Driver's Door Won't Open from the Outside.
    Was it working before? If not try this; unclip the rod from the handle to the mechanism at both ends and remove it, reinstall it the...
  • Adam
    Adam reacted to chessyxcuda's post in the thread Newbie with
    Like
    Like
    .
    Greetings to all. One of the newbies here, cross pollinated from Cuda-Challenger.com. I've got a 74 Challenger, triple black 360 4 spd...
  • Adam
    Adam reacted to brotow's post in the thread Engine install question with
    Like
    Like
    .
    I built a dolly for the motor and transmission and k frame. raised the car and rolled the dolly under, lowered car and installed. One...
  • Adam
    Adam reacted to Daves69's post in the thread Engine install question with
    Like
    Like
    .
    FWIW, If you're going from the top with an assembly, pull the distributor. Another option is to raise the rear of the car to cut some...
  • Adam
    Adam reacted to Ronbo73's post in the thread Engine install question with
    Like
    Like
    .
    I did mine from below, lowering the car onto the eng/trans and K-member. It was super easy with no problems and I didn't have to remove...
  • Adam
    Adam reacted to moparleo's post in the thread Engine install question with
    Like
    Like
    .
    A' It also matters if you are doing it the hard way or the factory way. Best way is to drop the K-frame and install the engine on it...
  • Adam
    Adam reacted to rickseeman's post in the thread Oil Pressure Low with
    Like
    Like
    .
    I think you've ran it enough. From here I think you should diagnose by turning the oil pump with a priming tool and a 3/8" reversible...
  • Adam
    Adam reacted to Challenger RTA's post in the thread Oil Pressure Low with
    Like
    Like
    .
    Pull the distributor and spin the pump to see if you have oil. It's a good tattle tell.
  • Adam
    Adam replied to the thread Oil Pressure Low.
    Only a couple of things could cause zero oil pressure all of a sudden. I would mark the edge of the distributor and pull it out...
  • Adam
    Adam replied to the thread About trunk lid reproduction parts.
    I had an AMD lid and it was excellent, but that was 15 years ago. You get what you pay for usually… That OER lid must be very cheaply made.
    • 2976053C-8F38-4BA3-BE70-F50DDB56F8C6.jpeg
  • Adam
    Adam reacted to DetMatt1's post in the thread One more time for TDC with
    Like
    Like
    .
    I think you are still over complicating this. Since I know now that this isn’t a fresh engine and wasn’t disassembled just get number...
Show older items
Back
Top