• Welcome to For E Bodies Only !

    We are a community of Plymouth Cuda and Dodge Challenger owners. Join now! Its Free!

Recent content by cool72

  1. C

    FOR SALE 1971 Challenger rear molded side panels

    Rear 71 Challenger panels in fair to good condition (both sides). $200.00 +shipping from 21122. Will send additional pics if needed
  2. C

    FOR SALE Big block Holley 4749-3 Carburetor

    Holley big block 4749-3 Carburetor. Good condition but could use a going through. $125.00 + Shipping from 21122
  3. C

    1971 Challenger headliner

    Tried to install a headliner, though to be for an e body. 5 bow no clips. After getting started and connecting the back bow with the two rods (all the rods are in and in place) I pulled the top forward and none of the rods would stay up, they all leaned forward like there is to much space...
  4. C

    First time starting

    I think so too. Removed the header, cleaned the header bolts and applied thread sealant. I have 10 psi on the system and am watching for leaks. I Don't think it is the HG
  5. C

    First time starting

    Removed the headers and realized that all the header bolt holes are connected to the cooling passages. It may be possible that the header bolts were leaking coolant. That would be a break. Some past history, the engine leaked when filled with coolant, just sitting there. I am going to remove...
  6. C

    First time starting

    Got the engine to run and it did not sound bad, however the whole time I have been working on the car/Engine I notice a small drip coming from the pass side. It appeared to be coming from one of the head bolts. Figured it did not have thread sealant on it. But as the engine continued to run...
  7. C

    First time starting

    Continuing on, could be a faulty neutral safety switch. Had it started, no problem. Continued to fill trans with engine off. Started backup and shifted in reverse no problem. Shut engine down, added more trans and tried to start. Engine turns over but no start. Is there a simple way to...
  8. C

    First time starting

    Worked 3 hours on starting the engine. Had it started twice. Second time it ran until we shut it off to add more trans fluid and connect timming light. Could not get it restarted. Figuring the wiring is ok we checked the voltages. They varried from 11.6 to 6 volts at the pos of the coil...
  9. C

    First time starting

    Great detail, thanks much. I will post my results when the engine runs. Thanks again
  10. C

    First time starting

    Thanks, I have to identify the cranking wires which should go to the starter then the running wires (other side of the resistor?) Where I also connect my ignition/tech wire? Sound ok?
  11. C

    First time starting

    Engine came out of a Mobil, ran but needed work. #1 was Tdc. Clear fuel filter, fuel getting to carb. I am in the process of confirming the wire locations. There are two balast resisters on the firewall, I think that may be the issue. In the process of upgrading to 700 cfm. Thanks for...
  12. C

    First time starting

    I have a 71 Challenger, auto trans, 440, Holley 600 cfm, electronic dist. Motor was completly overhauled and now produces around 375/400 hp ?? Installed the distributor with #1 cylinder on compression and rotor pointing to #1 cylinder. First attempt backfired through the carb, moved...
  13. C

    SOLD 'Cuda gas tank, heater box, k member, more.

    Do you still have the heater Box? E mail godeep20w@verizon.net
  14. C

    SOLD 'Cuda gas tank, heater box, k member, more.

  15. C

    SOLD NOS front/side marker sets, inner fenders, tank + used & cuda parts

    Looking for e body heater box, non a/C. Live in MD may need other parts send e mail Godeep20w@verizon.net
See more
Back
Top