Recent content by Ges2343

I added a second low pressure high volume pump and stabled the fuel pressure. Still haven't actually took it down the road because I started to transition to a non step side bed with fast tank outside of the cab. Second my wife gave birth 2 our second child which has limited my me time. Also I...

A little quick update. I got the y pipe with the o2 sensor today and installed it. Fixed a couple issues it had from sitting and a leaky transpan. Took it around the yard it did fine. Went out on the road it stated bucking badly. That inline pump don't like to suck and I believe the fuel...

OK as promised here is the video Fuel pressure stayed at around 59PSI. Until the O2 sensor is installed I believe the slightly higher fuel pressure with cause a rich condition. I let the truck run for about 20 minutes and took this video. Most of the video shows pids on the scan tool along with...

fuel parts came in yesterday here is a pic of most of the stuff. Your going to have to be creative on your own on how you want to do this I went the budget route and will probably upgrade later on to some more rugged line like braded ss and russel fittings. ive got about 35$ in the line and misc...

I rigged up a bracket I made out of piece of the knee bolster in the Dakota to mount the PDM to the driverside fender Here is the 3 wires that have to run to the PDM. 2 come from C3 and are the fuel pump and ASD trigger. the 3rd one comes from c105 and is hooked to a 10 amp fuse in the pdm for...

Here is the harness laid out so you all can see them Here is the starter harness I picked up some supplies from lowes. there wire loom is pretty cheap like 1.50 a pack a lot cheaper than the auto parts store. heat shring is half the price too. ok first thing I did was put heat shrink on all...

Alright so last night I cut the Power Distribution module out and brought it in the house. This doesn't have to be used but I figured it would neaten things up and would be easier than dangling wires with relays on them and fuse holders so here is a pic of the PDM. Here my finder is pointing to...

Ok engine is in and bolted up. So next I stated on the accelerator pedal I cut it out of the fire wall of the Dakota with an air saw. I hammed it flat and trimmed it up with some tin snips it will cover the 1.5" hole in the firewall and use all the factory holes only one will need to be...

Now I have the magnum engine is in the 73. I still have to bolt it all up which I should be able to get done tonight.

Ok I got home a little early and started getting some more done last night. I got the motor out of the dakota but before it can go into the hole in the 73 we have to do some simple modifications. First for the crank sensor. You will notice the Sensor protrudes into The bell housing. I used a...

Ok here we go I had a bit of delay if you zoom into the top left of the air cleaner. That is a pretty nice sized wasp nest which delayed me about an hour after I had to swat them down with a broom. I couldn't find a can of carb cleaner or brake cleaner or they would have been taken care of...

Here is the 73 dodge truck. Didn't get it here until about 7pm Here is the 99 Dodge Dakota SLT donor truck Underhood of the 73 Underhood of the 99

Alright then I'll start tomorrow. I'll get the motor out. I'm leaving for the beach Monday so if you guys don't see any info for a couple of days you know why. Biggest thing now is getting the truck here to the house. Or I would have already started.

Let me start here by saying im not selling anything. Im not even installing in a e body. If anyone has any interest in this Im willing to document the process. Im just seeing if there is enough interest to post how to do it. I have read where people have done 95 and below but I think the...

Looking for a nice cuda but not show car. Doesn't have to be original #s matching car. Performance add on a plus. Just no drag cars with cages and tubs. Good paint and body and I could iron out the rest of the car. No long term projects. Budget is 20k. Preferably black, silver, green or blue...