• Welcome to For E Bodies Only !

    We are a community of Plymouth Cuda and Dodge Challenger owners. Join now! Its Free!

Search results for query: *

  1. S

    MSD box location

    I custom built them for each application based on which MSD box the person was running and if the car was an air conditioning car or not. They are machined out of a 3/8 plate of aluminum.
  2. S

    MSD box location

    I have built a aluminum plates for a few different e-bodies to mount MSD ignitions in the place of the stock electronic ignition module. This gives a good way to install it with the rubber vibration isolators and not have to drill extra holes in the firewall/cowl for the car.
  3. S

    1970 Calif tank => venting options

    Options 1 and 2 are really the same in terms of the tank. Hooking up the 4 lines to the ECS tube in the trunk and then blocking the line to the engine compartment effectively seals that volume, just the same as capping the 4 tubes at the tank. In either option 1 or 2, you still need to run a...
  4. S

    WTB Stage V Hemi Rockers

    Thanks, I had talked to him previously, but will reach out again and see if something changed.
  5. S

    WTB Stage V Hemi Rockers

    I am looking for a full set of Stage V Hemi Rocker Arms. If anyone has a set they are willing to part with, please let me know. Trying to build a motor and that is the last of the parts to source for it. Thanks Scott
  6. S

    FOR SALE Cuda decklid and front brakes

    It is about 47 lbs per side, so I would say 100 lbs total, give or take a little.
  7. S

    FOR SALE Cuda decklid and front brakes

    Trying to clean out the last of the parts from the garage that I won't need. I have an original cuda decklid off a 70 car. It does have the normal rust on the lip behind the trim, but other than that appears to be pretty solid. Also have a front 11x2.5 drum brake setup (spindles, drums, etc)...
  8. S

    Good evening from Rapid Transit

    Welcome from another Tennessee Cuda owner.
  9. S

    MSD 6AL2 Box Mounting

    70RT4SPD, I will send you a PM
  10. S

    MSD 6AL2 Box Mounting

    I built a bracket for two of my friends cars to mount an MSD ignition using the factory holes in the firewall for the OEM ignition bracket.
  11. S

    Recomendations on which 4 link

    I agree with Mopar Nut on the Reilly setups. I have installed them on a few cars now. All ride great, and the installation/setup of them were not too difficult.
  12. S

    Gas pedal cable attachment

    Thank you. Not sure how I didn't find that looking around, but exactly what I was looking for.
  13. S

    Gas pedal cable attachment

    Thanks. Have you ever seen where you can order one of them? I must be looking under the wrong key words as I sure can't find one anywhere.
  14. S

    Gas pedal cable attachment

    At the top of the gas pedal, where the throttle cable attaches, there is a large hole for the cable end to slide through then the slot that it goes into to hold it. Was there a plug that is supposed to fill the large opening once you get the cable captured in the pedal? My pedal doesn't have...
  15. S

    Steering column adapter?

    I don't know about a splined adapter, but the Reilly Alterktion setup includes an adapter to go from the stock shaft to a double d universal. When you remove the original coupler, you put a shoulder bolt where the original press pin was in the shaft. I suspect he is getting it from Flaming...
  16. S

    WTB 70/71 Cuda rear bumper guard reinforcement plate

    I am looking for a pair of the reinforcement plates (and the bumper guard brackets too for that matter) for a 71 Cuda that go behind the rear bumper where the bumper guards bolt to them. There are several places that sell just the bumper guard brackets, but the only kit that really seems to...
  17. S

    Passenger Inner Fender part

    Thanks, I hadn't seen that goodmark made it different before. That is an option if I can't find an original to cut that piece out of as well.
  18. S

    Passenger Inner Fender part

    As part of the replacement sheet metal for my car, I had the passenger inner fender replaced. I didn't catch it at the time, but the replacement panel doesn't have the corner above the shock notched for the emissions tube like the factory one does. Has anyone else run into this issue? Does...
  19. S

    Shoulder belt storage clips

    Excellent, thanks. I found a set of them and was able to add the holes that were missing. For some reason, my car had holes for both driver side brackets, but only the rear one on the passenger side. The front one was missing.
  20. S

    Shoulder belt storage clips

    It looks like I am missing a bracket that had me confused. I have the set for below the headliner, but wasn't aware there was a second bracket that went above the headliner. That is what had me confused as there are two vertical holes in about the right place, but the brackets I have use a set...
Back
Top