Hello,
I'm looking for a vendor or information on making SE trim clips for the tops of both doors and quarter glass areas. These are the SE trim pieces on the 1970 1971 Challenger's. I called R/T Specialties and they do not have them or know of anyone who does? It was recommended that I...
Hello EV2RTSE,
Happy New Year and thank you for this information. This confirms what I suspected! The owner of the transmission failed to send all of the identification numbers. However, this gives me enough information so I can make an appointment to take a look at it.
Thanks again...
Hello,
I'm interested in buying an A904 transmission in my area. The owner gave me the following transmission numbers to identify what the transmission originally went to. I have a couple different versions of the "Chrysler Corporation Identification Numbers" to help, but can't seem to...
Hello,
Does anyone have a template and mounting instructions/dimensions they could share for body panel louvers on a 1971 Dodge Challenger R/T. These are the louvers that mount on the body in front of the rear wheels. I'm looking where to correctly mark and drill the four holes for each...
Hello,
I'm looking for a vendor who sells the correct nut and cage parts for the front frame rails on my 1971 Dodge Challenger. These are the four nuts that are attached/connected to the front frame rails where you bolt the front bumper brackets to. I have the mounting bolts, just missing a...
Hello,
I'm looking for a vendor who sells the correct nut and cage parts for the front frame rails on my 1971 Dodge Challenger. These are the four nuts that are attached/connected to the front frame rails where you bolt the front bumper brackets to. I have the mounting bolts, just...
Thank you to all that replied to my question. I'm planning on taking a closer look at these manifolds this afternoon. I appreciate all the help!
Regards,
Tirekickertoo
Hi
Hi Challenger RTA,
Thank you for the reply. Question, the 340HP manifolds I'm interested in were for A-body 1968 to 1970. Some research I've done show the part number working for a 1970 E-body I have a set of 1970 T/A head pipes in storage. Since the manifolds were made for 1970...
Hello, I have an opportunity to buy a pair of 340HP exhaust manifolds. The owner said that they were from a 1968-60 A-body car. One manifold has part number 2863552, the other is not legible. Initial research said that this part number will fit a 1970 Challenger. I’m working on a 1971...
Hello,
I have a chance to buy an original drivers side front fender for a 1972-1974 Dodge Challenger. Is there a stamped manufactures part number on this fender? If so, where can I find it? Please send picture of the location. How could I decode the part number to tell me what year it...
Hello,
Question, I have a small block (318) A904 TorqueFlight automatic transmission made in early 1970. I also have a small block (340) A727 TorqueFlight automatic transmission made in mid 1971. Are the transmission fill tubes and dip sticks interchangeable between these...
Hi moparleo,
Sorry for the delay returning your message. The problem started when we were running 14" rims. The rims came with the car when purchased and a tire shop informed us that one of the rims was slightly bent. The front end of the car was completely rebuilt. New MOOG problem...
Hi Moparleo,
Thank you for the advice and attachment. We are working closely with the shop manual to determine the cause of a severe front end vibration issue at about 50 to 55 MPH. All steering components were replaced not too long ago. It appears and feels to be the drivers front, but...
Hello,
Would someone send me pictures of the position of the inner and outer tie rod ends as they are connected to the drag link. I found a drawing in the shop manual but want to see a better example of this. Also are the tie rod adjusting sleeve suppose to be parallel with the ground or...
Hello,
The old bushings pressed out without issue. The upper control arms holes are round and I don't see any damage. Measuring the OD of the new MOOG eccentric bushings with calipers, the new eccentric bushing are about .045 larger in diameter than the hole on the upper control arm.
Hello,
What is everyone using using for upper control arm bushings? I have a 1971 Challenger with factory upper control arms. I want to install MOOG K7103 eccentric/offset bushing but can't seem to get them to press in without pushing/tipping to one side. I have all the correct busing...
Hello, I have a connection that has few manual transmissions for sale. What are the identifying casting numbers or other characteristics I should be looking for in a 4 speed manual transmission? My contact may also have other manual transmission parts available including the clutch and brake...
WTB, Looking for a Challenger passenger door belt line trim piece in good condition. I'm also looking for the hardware that attaches all four pieces. Not sure if the hardware is reproduced at this time?
Thank you,
Tirekickertoo