• Welcome to For E Bodies Only !

    We are a community of Plymouth Cuda and Dodge Challenger owners. Join now! Its Free!

PST's Stiffening Plates Install

PST

Well-Known Member
Joined
Jan 4, 2012
Messages
106
Reaction score
15
Over the weekend Guys I decided to clean up a lower control arm that we had, so our sales staff had an example to refer too. I hope this helps you guys out as well. Please practice all safety precautions when performing this installation


Thanks
James


So what do these parts have in common? Why go with a Mopar tubular lower control? When with these cost effective parts from PST you can achieve the same performance. This weekend one of our employees will do step by step posts on how easy it is to do. So stay tune
moparlowercontrolarm-somethingsomething_zps3cb255d6.jpg



With the pivot shaft removed, now you will have to remove the lower control arm bushing and inner sleeve( on this build we will be installing a PolyGraphite bushing so we will be re-using the outer shell) Many people burn the rubber out, but a cleaner and easier way is with a heat gun. Direct the majority of the heat into the center in sleeve for a few minutes.
IMG_20130223_085719_zpsc2c7beec.jpg



Now that the inner steal sleeve is nice and hot, take a vise grip and grab the inner sleeve and twist. The inner sleeve will easily come free. Once that is free use a pic or thin bladed screw driver and go between the outer shell of the bushing and the rubber center. Then remove the rubber with vise grips.
IMG_20130223_085922_zps60a62fce.jpg



With the control arm clean and free of rubber, take PST's stiffening plate and center it over the back of the control arm. Make sure to have adequate room to allow access to the torsion bar adjuster and control arm bumper. Use multiple vise grips or clamps to hold the stiffening plate flush to the control arm
IMG_20130224_093201_zps274b1967.jpg



After double checking the placement of the stiffening plate make your initial spot welds to hold the plate in place.
IMG_20130224_093617_zpsc8a797e2.jpg



Now with the stiffening plate secured, start welding either side of the plate till completely welded.(Click on the picture to view video)
th_VID_20130224_122357_zpsa265f5bc.jpg


Make sure that you have proper weld penetration of the plate to the lower control arm.
IMG_20130224_122713_zps2038347d.jpg



With welding completed it's now a matter of appearance, in this case I used a grinder with a sander paper flap disc and smoothed out the welds to give a seamless appearance.
If you have any question please feel free to contact us at 1-800-247-2288 or www.p-s-t.com
IMG_20130224_135234_zps426806f2.jpg



Finished cleaning the welds up and gave the control arm a fresh coat of chassis black paint. Stay tune tomorrow I will be installing the PolyGraphite lower control bushing, pivot shaft and torsion bar adjuster. Just a few simple upgrades and you have a control arm that ready to perform in any situation.
James
PST
1-800-247-2288
jfrom@p-s-t.com


IMG_20130224_215234_zps2d567d63.jpg
 

PST

Well-Known Member
Joined
Jan 4, 2012
Messages
106
Reaction score
15
Well I had some time to make out to the shop today and finished up the lower control arm build. So here it is new pivot shaft, bushing, torsion bar adjuster and stiffening plate. It is a simple and great improvement to any mopar
www.p-s-t.com
IMG_20130225_151953_zps58205dd0.jpg

Thanks
James
 

Adrian Worman

Well-Known Member
Joined
Jan 29, 2012
Messages
155
Reaction score
6
Location
England
I saw this James and I just wondered if you offer a greasable lca pivot pin?
One small point I'd like to make to add to your already very good thread tho........
While you've got your welder out and the lca is removed from the car, please take some time to check the K member for missing welds and possible cracks, especially the areas where the factory welded the socket for the pivot pin, I've seen a lot that weren't safe due to poor factory assembly. It makes sense to do this, after all we are taking great pains to make our factory suspensions into a high performance system that relies on stiffness and stability to ensure it works how we want it.
Any extra stress on an unchecked factory K member would leave me a little uneasy, just my '2cents worth' as you nice Americans say :)
 
Back
Top