WTB wanted 1970 barracuda side scoops m 46 option

[71cudaguy]

I sold 2 sets years ago now I need a pair for my next cuda. thanks any leads would be helpful

 

[Cuda Hunter]

Welcome from Colorado.
Maybe wander over to the introduction section and say hi.

 

[70chall440]

Need to get someone to 3D print some

 

[1972CudaV21]

Need to get someone to 3D print some

I bet that’s doable.

 

[340challconvert]

71cudaguy
to FEBO from New Jersey
The m46 scoops are one of those "unobtainables" that come up for sale on rare occasions
The 3d printing could be the solution!

 

[Cuda Hunter]

Scott does reproduce these once in a while in small limited batch's.

@71cudaguy Are you willing to use a set of reproduced scoops?

 

[71cudaguy]

Welcome from Colorado.
Maybe wander over to the introduction section and say hi.

I know they are stupid rare. Bone head move to sell them[ both red] They never got to the cudas because of an error in the order book. yes repops would work for my car. Thanks

 

[71cudaguy]

Scott does reproduce these once in a while in small limited batch's.

@71cudaguy Are you willing to use a set of reproduced scoops?

Scott Smith?

 

[Cuda Hunter]

Yes, Harms auto. If you call and he is making up another run, please report back here as I would like to purchase another reproduced set from him. As I understand he has changed the molds and the new scoops are better than the first ones he made. As I have read.

 

[71cudaguy]

Yes, Harms auto. If you call and he is making up another run, please report back here as I would like to purchase another reproduced set from him. As I understand he has changed the molds and the new scoops are better than the first ones he made. As I have read.

ok Thanks

 

[Cuda Hunter]

And I'm dying to know more about your M46 car.
I would love to add it to my M46 registry.
If you had scoops some years ago, you might also have information on other M46's from the past. Any information about the M46's would be very much appreciated.

 

[71cudaguy]

And I'm dying to know more about your M46 car.
I would love to add it to my M46 registry.
If you had scoops some years ago, you might also have information on other M46's from the past. Any information about the M46's would be very much appreciated.

mine is not an M 46 I just want them. It's a tx9 n auto air It's going rubber bumpers rear louvers side scoops aar trim in black.I built one like this for a movie company it looked very sharp.

 

[71cudaguy]

mine is not an M 46 I just want them. It's a tx9 n auto air It's going rubber bumpers rear louvers side scoops aar trim in black.I built one like this for a movie company it looked very sharp.

I sold a pail to a guy in oregon and he had some of the cars

 

[1972CudaV21]

And I'm dying to know more about your M46 car.
I would love to add it to my M46 registry.
If you had scoops some years ago, you might also have information on other M46's from the past. Any information about the M46's would be very much appreciated.

Any numbers of how many 1970 Barracudas came equipped with them?

 

[71cudaguy]

Any numbers of how many 1970 Barracudas came equipped with them?

No I don't think even Galen has that one. The guy in Oregon was up on them but I don't know his name. I think he had 2 of them.

 

[Cuda Hunter]

mine is not an M 46 I just want them. It's a tx9 n auto air It's going rubber bumpers rear louvers side scoops aar trim in black.I built one like this for a movie company it looked very sharp.

That will look super sharp!

 

[Cuda Hunter]

Approximately 400 produced.
I have 4. 3 rusty time capsules and one awesome car! Not restored to original though unforunately.
I'm always looking for another one!

 

[Cuda Hunter]

If you would like to learn about the scoops, here is a detailed report.

M46 scoop details in Body Shop

Page 1 of 4: I've been asked for specs on the M46 scoops. Mounting studs, screws and nuts. I'm not sure of the thread sizes yet but I will go to the hardware st

forum.e-bodies.org

 

[Cuda Hunter]

And here is a list of the known cars that I have been fortunate enough to gather info on.
From what I understand Barry with the hamtramck registry has some build sheets for m46's but he won't share a single detail.
I am always looking for leads on these cars. Just for my "registry" of sorts that I have not made a site for yet. Any info, any contact info. Any old polaroid pictures! Anything! Factory information?

The M46 list in VIN, Fender Tag, Build Sheet & Date Codes

After several folks have asked to see the current list I figured I would just make a thread for the list I have. There is all kinds of info on the ot

forum.e-bodies.org

 

[Cuda Hunter]

Mods, if the search feature here would let me search m46 I would just post the thread I have here for the list, but since the search engine kinda sucks I just searched it over on ebodies.org and posted it here as it was very easy to find with their search engine. Just sayin.