Search results for query: *

Hey all, quick question on a steering column. I know Flaming River and ididit both make columns for the e-body but they are very expensive. Ididit has a universal 32-in column that is almost half the cost for a retrofit unit. I don't necessarily want a keyed column either because I plan to do a...

Hey all, I'm going to run an electric power assist master cylinder and need to figure out a way to mount it. The master cylinder is a standard 2 hole but I have multiple holes on the firewall. It's been a while since I took the car apart and of course I can't find the plate I had. Does anyone...

Hey all, I'm building my Air intake and looking for ideas. I purchased a universal K&N cone filter but it looks small to me. What are you running?

Hey all, I'm selling the k-memeber I removed from my car. It had a 318, power steering, great condition. Comes complete with the torsion bars, control arms, exactly as pictured. Located in San Jose CA. I NEED THIS GONE!!!. I'm not sure what these are worth. I see prices all over the place...

Hey all, need your opinion on the inner fender brace kit. I plan on either making or purchasing some engine bay down bars similar to the photos attached. Does it make sense to install these with the US-Cartool inner fender brace kit? Seems like they would be doing the same thing, just attaching...

Anyone looking for Delete panels, check these out. I just received them from Resto-Nerd High-Quality Restoration Parts & Accessories for Mopar Vehicles | Resto-Nerd Muscle Car Worx. Really nice 3d printed panels and communication was stellar. I'll try to get some photos of them when I install...

Anyone running a 4 link in the rear ever remove the old shock tower crossbar? The one that sits in front of the gas tank? I'm having a hard time trying to plumb the fuel lines from the tank to my filter and Ethenol sensor. I was thinking I could remove it and replace it with a round one bar...

Hey all, I'm looking to add some vents in my non AC dash. I'm looking for any ideas or photos of what you have done. I came across the vents in the link below on another thread. Do I need an AC dash frame or can I install them in my non AC dash? I see the car below installed some round vents...

Hey all, can you help me locate a spot for a coolant temp sender. There is a plug on top of the thermostat housing but I'm not sure if that's the best location. If the thermostat was closed would the temp be accurate? Motor is a hellcat. Thanks in advance.

Hey all, I'm trying to figure out the best way to run my fuel line. I'm running -8AN (1/2") stainless braided PTFE. I also have US Cartool subframe connectors. Is there any issues running it along the outside rear frame rail to along the subframe connector to the front? This would be similar to...

Hey all, thinking about going with an electric master brake set up instead of hydraboost. Trying to keep the engine bay clean as possible. What do I need to convert from the 4 bolt to two bolt cylinder? There is a large plate I believe was used to stiffen up the firewall as well. Is that removed...

Hey all, is it ok to to use hood pins without a latch? I'm trying to make room for my condenser and heat exchanger for the supercharger. It would give me a lot more room switching to hood pins and no latch. I could remove the center bar behind the grill. Thanks in advance.

Hey all, I'm installing my trans and having a slight issue. As I jack up the trans into the tunnel it pushes slightly to the pass side and starts to hit the brace. Does anyone have any suggestions on how to fix? Running RMS front K member 1" forward mounts. Using holley trans crossmember and...

Hey all, I'm looking to convert my non Rallye gauges to the Rallye style. I'm doing a hellcat swap and want the nicer gauges from dakota digital. Wiring harness doesn't matter to me as I'm Wiring the car with a harness from american autowire. Does anyone sell the cluster parts to do this...

Hey all, has anyone shaved their firewall and relocated the wiper motor? I'm in the middle of my swap and stated filling all the holes. Problem is the factory shertmetal is paper thin so I'm not too happy how it came out. Since I'm going to redo it, I'm thinking I want to shave it completely and...

Hello all, can anyone help me identify if these stamps are legit. The only one I'm really questioning is the engine block stamp. It looks as though the last digit (3) was stamped twice. Other than that everything matches from what I can tell. I don't have the build tag on the fender as the car...

Hello all, I'm getting ready to start on the rear suspension and have some questions. I'm moving the rear 4 link control arms inboard with the brackets provided in the kit. I'm a little confused on the way they weld in. There is a bracket on the outboard side of the frame that looks to be part...

Does anyone know where to get theses bars from? I've only found them at Magnumforce so far. I'd like to get a pair to help stiffen up the front end when I put my new suspension in.

Well folks, My build journey will begin here. I received 10 boxes from Bill @ Riley motorsports a couple of days ago. I went with a complete front clip and rear streetlynx set up. 14" 6 piston willwoods all around will be the stopping power. I can't wait to get started on this build. Once I...

For those that have done a hellcat swap, what harness did you use? I was looking at the Mopar performance harness kit with ECU ECT but not sure on the length. Most swaps I see the ECU and power bloCk is mounted in the engine bay. I want to mount everything under the dash and I'm not sure the...