Search results for query: *

I want to use my original vapor separator. Car is for occasional cruising. Questions: 1. Is using my original a good idea in the first place. Should I only use a new repro? 2. If I use my original, what is optimum way to clean it out internally without damage. Carb cleaner for example? 3. Does...

My original Rallye gauge tach is reading about 2 times too high. Set the idle RPM to about 850 (using 30 year old Sun meter) and the dash tach is showing about 1400. Any suggestions would be appreciated.

Have an Edelbrok AVS with electric choke. Where are the best positive and negative connecting points for the choke? I’ve read so far ballast resistor or wiper motor for positive side, but looking for best practice. Thanks

1970 440-4 engine. Was the choke assembly installed on intake and painted with the engine? Masked off anywhere? Thanks

Anyone suggest LED replacement bulbs for the Rallye light bar that are a bit brighter than the incandescent bulbs but not too bright? or does LED totally change the green hue through the plastic lenses?

Rallye Gauges and A01 package. Map Light, Ignition Switch Light and Light over Headlight Switch Panel not working. Maybe having to do with this relay shown in the picture? Not seeing it in the electrical diagrams but I’m sure it’s there. Let me know if this could be the culprit and the name of...

Anyone find a home black phosphate kit that does a decent job? Want to do a bunch of my car fasteners but read many mixed reviews on the DIY kits. Many say the color comes out brown or grey and not black. Thanks

Link or pic of the underside frame and body dimension diagram for 1970 Challenger? Really appreciate it

Couple questions on front parking lamp assemblies (1970 Challenger): #1 Date codes. The Right housing has numbers on the left tab. The Left housing does not. I suspect one or the other may be a replacement. Let me know what your 1970 might have. #2 Lense screws. Not sure if the screws I have...

Anyone have the paint code for the factory primer? or is there anything off the shelf from PPG or other that matches? Thanks

So, was I supposed to run the carpet over the 4-speed bracket? or its supposed to be painted black? or I did it correctly?

Just noticed the rear bumper guards are not totally symmetrical when looking up from the bottom. I haven‘t looked for a L and R stamping on them yet, but does anyone know if they are designed L or R, or are they interchangeable L and R ?

Want to clean up and restore my Center Console and want to be careful with any solvents that may damage the plastic. Anyone know the plastic type? I believe it is Polypropylene, but could be totally off.

Restoring my 1970 center console. Have two doors. One on left is dated 11/69. One on right is dated 4/70. Didn't realize that they may have used 2 different locks. Questions: Are they both correct? One or the other correct? or neither correct? Thanks

Cheap aftermarket plastic valve (intake hose) broke off at the booster. Half of the valve fell into the booster. Please let me know if this will damage the inner diaphragm, or will be harmless? Need to decide if I have to remove the booster and get this piece out somehow. Thanks

Have manual steering and my 50 year old worn down standard steering wheel. Really difficult to turn, and the worn down plastic wood wheel is really slick. Is the optional Rim Blow rim any larger in diameter for better grip? Is the grip better in general than the standard wheel? Are the repop...

1970 440, stock, fully rebuilt, couple hundred miles since going in the Challenger. So been chasing a vibration/roughness issue. Idle is OK, but over 200 RPM, engine get progressively worse in regards vibration/roughness. Checked timing, dwell, plug wires, tuned carb, multiple times. No real...

Heater Blower Motor not running. Going to start by checking ground. Non A/C Where exactly is the factory ground for the blower motor? Is it the engine side firewall? The 3 nuts need clean ground (no paint) to the firewall? or is the ground somewhere under the dash? Thanks

Fuel Gauged pegged to Low side. When ignition "on" gauge needle moves very slightly up, but very, very little. Checked Ohms on Sending Unit (between sending unit post and ground) and reads about 25 Ohms. I believe that means there should be some fuel in tank (range about 10 Ohms tank empty to...

Are the interior door panels Polypropylene? or other plastic type? Best adhesive you have found to repair door panel cracks? Thanks