• Welcome to For E Bodies Only !

    We are a community of Plymouth Cuda and Dodge Challenger owners. Join now! Its Free!

Recent content by cudablue

  1. cudablue

    SOLD Heater-core, Keith Black pistons, emblems, oil pan, exhaust, bell housing, valve covers, misc parts

    Got a variety of parts. I want to sell the whole lot. Here in Woodstock, GA Heater core HVAC unit – like new. 8 Small block Keith Black Pistons .30 over Only 500 Miles 2 Side Windows (2 doors and 2 back seat)– frt door LH side is tinted. fair Small block exhaust manifolds – very good...
  2. cudablue

    SOLD 1971 CUDA, True 340 4sp B5, V6W

    On the ebay motors block! Plymouth: Barracuda CUDA ‘Cuda Video: 71 Cuda2.m2ts Video shows Gold engine. I just repainted it. HEADS UP. It is a true 340 4speed CUDA car from the factory. Matching numbers except for the 360 engine. An era correct 340 block (with minor repairable crack) will...
  3. cudablue

    1971 Cuda 340, 4 sp, blk int, white billboards.

    1971 Plymouth Barracuda ‘CUDA $65K OBO EBAY MOTORS: Plymouth: Barracuda CUDA ‘Cuda Video: 71 Cuda2.m2ts More pics link: 1971 CUDA It is a true 340 4speed CUDA car from the factory. IT HAS A 360. Matching numbers except for the engine. An era correct 340 block (with minor repairable crack)...
  4. cudablue

    Help! Jet 850 down vs jet 670 up vs buy 750

    Thanks for the input guys!
  5. cudablue

    Help! Jet 850 down vs jet 670 up vs buy 750

    Hello gang, This is kind of a spinoff from my other thread. "sputtering issue with new carb". Holley 870 vac,: I jetted down to 78 primary/82 secondary from 82/82. Sputtering was better, but still did some. Can I jet down further? How do I know if it's too lean? Holley 670 vac: I jetted up...
  6. cudablue

    Sputtering issue with new carb/motor. Need advice. Bad Carb?

    Update: I jetted the 870 to 78 instead of 82. The hiccups got better. I'll try 77 next.
  7. cudablue

    Sputtering issue with new carb/motor. Need advice. Bad Carb?

    I put the 670 on and rejetted it to 70 primary and 71 secondary. It ran perfect! but very lean and the temp went up about 20 degrees. I called Holley and they said its not recommended to go up more the 4 to 6 sizes. It came with 63. Can I go higher that 70? Today I will try the 870 again and...
  8. cudablue

    Sputtering issue with new carb/motor. Need advice. Bad Carb?

    Hey guys, no vacuum advance. At idle I believe vac it is 13. I don't know what 3K RPM is, but will check and get back to you. I have been reading alot about the 180 vs 160 and more confused before I started :P. I will install the 180 first. I do have a couple of Carb options. I have a brand...
  9. cudablue

    Sputtering issue with new carb/motor. Need advice. Bad Carb?

    Hello gang, When diving the carb will sputter. I can cruise at any speed (40 to 80 mph) consistantly and out of the blue,,, it sputters for a split second and then is fine. It will do this at various times, but approximately every 45 seconds to a minute. Here are the facts. Heads up ,, I'm a...
  10. cudablue

    One piece oil pan gasket (sealant?)

    Thanks moparleo!
  11. cudablue

    One piece oil pan gasket (sealant?)

    Hello Gang, Got a '76 360 block. Fresh rebuild but the rear of the pan is leaking. I just ordered a Milodon one-piece gasket from summit. Can I put a little sealant in the corners? Any recommendations are appreciated. thanks, rick
  12. cudablue

    Header leak - I need advice

    I ended up cutting the sections out between the tubes. This took the curve and twist out. Now I am able to pull the flanges tighter against the head.
  13. cudablue

    Year One, A Closer Look

    Use 'm. I finished my full rotisserie 71 Cuda. J I purchased over $6K at Year One. I waited for the 30% discount emails and jumped on it. I anally laid out a full spreadsheet comparing up to 15 vendors and every part! When you hit the 30%, it usually beats allof them. They may be...
  14. cudablue

    Header leak - I need advice

    Just wrapped up. It's been a couple of hours for the sealant. Should I wait 24 hours to drive? Or, is it ok to go for it? thanks
Back
Top