Search results for query: *

Thank you. The blue and brown ended up being removed. a 90 minute call with Holley while real time options were tried may have solved problem. I‘ll post again when get real story from my mechanic.

I am electrically challenged but my mechanic is electrically savvy but we are stuck. I have Sniper with hyperspark distributor, hyperspark ignition box, and HSpark coil.(and Holley Efi tank/ in tank pump). Internally regulated, single wire alternator and Dakota digital dash resulting in mostly...

M6892F. I can’t vouch for them personally yet.

Thanks for the info. I googled the part number and ended up on the m/e Wagner website. It says unavailable. I talked to them yesterday and no mention of this grommet. He did suggest the Ford part. I also found a post on FABO where someone used the Ford part on these covers with Wagner. I found...

I have the mopar performance big block cast valve covers with a twist on hole and knock out spot on each. I am installing a m/e Wagner Pcv valve in one of the twist on holes. It needs 3/4” id. Does anyone know which grommet with that id also has big enough diameter to seal twist on tang...

I have TTI headers and am still trying to decide wire routing and boot angle. Not trying to duplicate original setup. I’ve looked at as many pics as can find. Looks like lots of people run them around front below headers vs running any over valve covers. I like cleaner look running under...

Thanks for the input everyone. Leaving it open.

restored my heater box and installed. A gap exists between it and plastic defrost plenum that goes up to windshield. Is that gap normally open or was some sort of gasket used. Nothing was there when I took it apart but most of the old foam in heater box had disintegrated and disappeared...

since I am already spending more than I want on resto, who doesn’t, I am going to tackle restoring my steering wheel. I have the 70 3 black rubber spokes with silver inlay, plain horn cap. I will attempt duplicating the wood grain, at least the overall impressions of wood if not exact. I have...

how important are the plastic film moisture barriers inside Cuda door panels? Since panels are plastic do they really need protection like styles that have cloth or cardboard backings? I saw a thread somewhere how to make them and found a kit on web, just wanted opinions. Not concourse resto but...

Anyone install the tank vent Holley supplied with tank? Where did you mount?

I want to replace windshield and all side glass in my Cuda convertible. From research, seems most are happy with ECS and AMD. some say they source from same supplier. What about Auto City Classic? I know they source from China also and they are cheaper but that worries me a bit. Anyone have...

I’ll take it. I sent a PM.

Do you still have empty fresh air box $10, picture #143? Thanks

Sniper not installed yet. A little behind schedule. Lot of other good feedback about sniper on this and other forums. I did find brackets at Mancini Racing that are designed for Performer intake. Haven’t test fit those either. So, I am a LOT behind schedule. At this rate I’ll have it road...

I ordered blower motor for 70 Cuda non a/c. Obviously some big differences in looks but more importantly the shaft for cage is longer and holds further out from motor so it rubs on inside of housing. The cage I took out of it is plastic...is it even original? I have only seen one picture of...

Not there quite yet but was thinking of using the original off the 340 that is getting replaced. Djais1801, I love the walk around video. I came across it a few months ago. Good to see and especially hear it again.

Thanks. I’ll check them out.

i am putting a Holley sniper on edelbrock performer rpm on 440 in 70 Cuda and was wondering if anyone has this combo. I have no throttle cable, return spring, brackets or linkage. What stock or aftermarket parts did you use?

I needed all 4 anyway and will probably do kick panels while I’m at it. Definitely will not be cheap but to have everything fit and look great is worth it considering how visible it all is, and how much I’ve already spent to make everything else look new. Still killing me how much all this is...