Search results for query: *

Has anyone used a vintage air kit on a 74 challenger to completley replace the factory air package ? and if you have was every thing there that you needed

Hi guys I have a little problem since I put a Comp cam in my 74 Challenger with a 440 I have lost so much vacumn I now don't have enough Brake pedal to stop safely in an emergency . Only about 11 to 12 lbs of vacumn, I have added a vacumn canister that helps some but still doesn't seem to be...

Thanks for the info it is very helpful

THANKS, I thought I had read in another post that you had said the 295s would work . But I didn't remember you saying that the fender edges had to be rolled . And I wondered about that I really think the 275s will suit my need since I don't intend to race anyway . I just want the back to be...

I honestly don't know I need help picking the largest 15 inch tire and wheel combo I can use with the American outlaw ll wheels to match the front 14 inch wheels and what back set I need with out altering the car Can you make a suggestion?

I honestly don't know I need help in picking a wheel I would like the widest tire and wheel combo I can use with out having to alter the car . And would like to use 2 of the American out law ll 15 inch wheels to go with the 14s on the front. Can you make a suggestion?

I have up dated post

What is the largest 15" tire that will fit my 74 Challenger without modifactions to the spring brks ? I have air shocks. Also if I use 8" American Racing Out law ll rims what back spacing will I need to ask for I am using 14x7" wheels on the front with P235/60R 14 tires on the front

Does anyone know the largest 15" tire I can use without modifaction in the rear wheel well of my 74 Challenger ? I do have air shocks No other mods and don't want to mod.

Wtb slap stick pistol grip shifter handle for my 74 Challenger anyone no of the manufacture .

I would like to buy the front cover for the heater/ac box that has the opening on the front for the center & right dash vents and the lower opening on the bottom left for the left dash vent . I also need the left dash vent tube both for 1972 thru 1974 challenger with a/c. as per pictures

First I am using electronic ignition, and a Holley Street Avenger carb. 770cfm electric choke that has a metered vacuum port so there is no vacuum to the distb. at idle. and yes it is a 440. I have not tryed your procedures I will wait untill I hear from you on this information to see if there...

Moparleo: Engine starts fine but runs a little ruff untill choke opens a little about 1-2 minutes, after that runs fine until driven for short time and engine comes up to normal temp about 180 degs. then after stopping and idleing at what seems to be normal in netural for a short time if...

I don't belive so we just got it back together after being torn down 12 years ago . I did have a problem with the timing when it was first started , it was off a full tooth on the timing set and the carb that it was first put on the engine was running too lean and causing the engine to run hot...

Hi Moparleo: I knew if you seen this you would know the answer. much recent work on car has been done car already had cheetah kit when purchased. just changed to forward patern kit because no kick .down linkage and I like to shift manually also new comp cam kit. and Holley 770 street avenger...

I'm having trouble with engine stalling after warm up when dropping in gear. Runs fine for a short drive then after stopping fo a few minutes and leaving motor run when put in gear motor dies. does this every time I restart unless I hold gas pedal down pretty far .And then the car will lunge and...

Rocky long time no talk. I am looking for a front trim cover for my 74 chally. The one that covers the heater core with the hole in the front for the dash a/c vents. for my ac/ heater box . I still have your phone # if it's ok I will text you a pix of what I need from the service manual. thanks

I will try some of the ideas when I get back . at present I am going to have to be out of town for a couple of weeks so I wont be able to work on it but thanks for the ideas. I will post again when I get a chance to start on it again. thanks again.

Yes I have a shroud. I had to modify the mounting brackets though because the holes did not line up even though I ordered the corect shroud from Year One . And no I did not replace the fan clutch. I was told that it would cool beter if I would just delete the fan clutch and buy a spacer and a...

thanks Chryco Psycho.I put them the way you sugested but since the heater core leaked I took them off and pluged the ends of the hoses. For some reason the engine over heats .so I thought maybe I had them wrong. I did not use a by pass hose instead pluged the hoses. I wander if the 2 nipples...