Search results for query: *

Wondering if it would be good to replace the carrier to axle housing factory nuts with the nylock type nuts. Factory didn't use lock washers, just tightened down to 45. ft lbs and I guess that's all that's needed. The nuts are pretty thick and probably have a lot of holding strength compared to...

Finally gave up on trying to bend aftermarket rear wheel trim to look halfway decent where the quarter panel makes a hard angle near the bottom at the rear of panel. I had bought original trim years ago and decided to check the fit on the AMD replacement quarters. After a little careful bending...

I have a green console that has a plastic loop installed on the right side. Has any one ever seen any other ones that may have this sort of thing installed or is it something that's been added.

I'm trying to determine what the small square metal piece that was installed under the main fender tag from my 71 Barracuda. It has a small hole punched into it. A buddy said it was put there for the engine guy on the assembly line to install a Hemi instead of the little 318 if they had any...

Checking to find out if someone might know what VX6 Fender code meant on a 71 Challenger RT. Decodes to black longitude sports stripe. Car is painted tx9 which is correct per fender tag but it has a white RT stripe on the side. Vinyl top is supposed to be V1W which when I purchased car had been...

Does anybody know where I can buy bumper guard fillers for a 71 Cuda. The ones I purchased have some cut marks on the sides where the excess flashing was removed. I don't remember how much of the filler shows next to the rear valance. Was told that they are all made at the same place regardless...

Need some help with a paint code for the metal trim that goes around the back window and along the top of the windshield and above the side windows. The car is a 71 Barracuda with a white interior. I took in a small piece of the headliner to the local paint store but they could'nt get a good...

Checking to find out if anyone has ever did any research regarding the two belts used used in the factory cassette players. Both belts have turned to a black goo, I found a link on Wards Radio Repair where the belts can be ordered, It would save a lot of time if someone knows the correct length.

Need air cleaner for a 71 Challenger 340, Have a 72 Challenger air cleaner for trade that I took off a friends car when I traded a holley for the factory thermoquad back in 74.

Will a manifold heat shield from a 383/440 fit a 340. I know they are made of thin metal but don't know if they could be modified to fit.

I need 1 71 Barracuda headlight bezel screw, does any one know if these are avalible?

Need left outside door handle, went to install new handles and can't locate leftside, need hardware that holds the lock and lock linkage.

I installed new roof rail weatherstrip rubber from Metro, it doesn't seem to fit like the original. Does anyone know who makes a weatherstrip that is closer in fit to what Chrysler used. Vehicle is a 71 BCuda, thanks

Checking to see if any one on this site is a running an electric fuel pump on their Challenger or Barracuda and have any pics they can share. I am going to purchase a set of brackets from Dean Gollnitz the Bracketman to stuff the ac compressor under the alternator. The compressor bracket mounts...

Can you use a 3 speed wiper switch with a 2 speed wiper motor? I'm changing out standard dash with a rallye guage cluster and harness.

Any one using Wheel Vintiques billet Chrysler 95 series wheels?

Body shop called today and said they were going to install top of door and quarter panel moulding but couldn't due to the trim not being curved enough to lay flat against the top of the doors. He tried to bending it to match the door and it broke. This is repro stuff so I don't know what to...

Does any one know how to remove thr quarter glass from the metal frame. I've tried heating it with a heat gun and then using a length of 2x4 and a hammer to try and to remove it. So far it hasn't moved any.

I picked up a set of Foose Legend wheels for my 71 Barracuda. The wheel sizes are 17x8 with 245 45 x 17 Nitto Extreme 555 tires for the rear and 17x7 with 235 x 45 x 17'' tires for the front. I installed the rear wheel / tire and measured 1 3/4 inches between the tire and the rear spring. All...

I picked up a set of Foose Legend wheels for my 71 Barracuda. The wheel sizes are 17x8 with 245 45 x 17 Nitto Extreme 555 tires for the rear and 17x7 with 235 x 45 x 17'' tires for the front. I installed the rear wheel / tire and measured 1 3/4 inches between the tire and the rear spring. All...